Craftsman 113.225931, 113.225909, 113.225900 Ge ng to know you r belt and disc sander, Lock NUt

Page 18

ge ng" to know you r belt and disc sander

fLoosen the table positioning lock screw., . posi-

tion the table approximately 1/16" awa_ from

/

 

the abrasive disc.

 

g. Tilt the table downward but don't tighten the ock screw, and position it as close to the disc as pos-

sibte. Using the head of a combination square,

check the angle of the table with the disc,

h. If the table is not 45 ° with the disc:

i.Raise the table and loosen the lock nut using a 7/16" wrench.

j, Screw the stop screw in or out, using a 3/8'" wrench so that when the table touches it, it is 45 °

with the disc.

k. Tighten the lock nut.

WARNING: To avoid trapping the work or fingers between the table and sanding surface, the table must

be repositioned on the rod to maintain a maxtmum

1/16 inch space between the table and sanding surface,

4. BACKSTOP LOCK SCREW locks the backstop in

place. It is locked u_ing the 1/2"' wrench,

5.BELT TABLE LOCKING BOLTS ... lock the belt table in position.

To adjust to vertical position:

a. Remove the backstop.

b. Loosen the two belt table locking bolts using the 1/2" wrench supplied with your machine.

c. Position belt table vertically and tighten the two bolts.

6, ABRASIVE BELT TABLE STOP can be adj- usted so that the abrasive belt table is level with the floor when in a horizontal position.

a, Loosen the lock nut using a 3/4"" wrench.

b, Place a level on the abrasive belt table and using a 314" wrench, screw the stop bolt in or out until the table is level.

STOP SCREW

BACKSTOPBACKSTOP

LOCK SCREW

\

BELT TABLE

LOCKING BOLT/

STOP BOLT

LOCK NUt

18

Image 18
Contents Belt and Disc Legs and MotorGeneral safety instructions Power toolsBefore Using the Sander Before Each USESander Whenever Sander is Running Plan your workAt a time Connecting to Power Source Outlet ProperlyGrounded /n Ul OUTLETs Contents Unpacking and checkingAssernbJy HAROWABEFORMOUNTINGTOOL& MotorFollowing parts are included with Model Mounting Belt and Disc Sander on Craftsman Steel LEG SET Catalog noWrench Installing Sanding Disc and Dust TrapAssembly Belt Table LockingDisc Dust Trap Flat Head Screws AssemblyFlat Spot TrapClips TOP Right Hand Screw Dust Trap CoverTWO Holes 10-32 X 1/2Insert key into switch AssemblyON-OFF Switch Place the bolt onto the motor pulley by rotating the pulleyPower Cord Motor Cord CableFind plastic cable hanger from among the loose parts Pull Wrenches in this Direction to Apply Tension Installing Work TableDirectional ARROW\ Be LT Adjusting SCR EWS Belt Locking ScrewBelt Locking Screw Drive Installing Belt Dust TrapBelt Leftmoving To Right PulleyGetting to know your belt and disc sander Installing BackstopAssembWy ANY Aojustm EntsBelt Adjusting Screw ONE on Each Side From Disc Positioning Lock Screw Stop Tilt Lock NUTPlace. It is locked uing the 1/2 wrench Raise the table and loosen the lock nut using a 7/16 wrenchGe ng to know you r belt and disc sander Lock NUtBefore Using the Sander Basic operationBefore Each USE For finishing long pieces, remove the backstop Surface Finishing on Abrasive BeltBefore freeing any jammed material END Finishing on Abrasive BeltCurved Edges Causing thebelt to sli Motor Maintenance LubricationSears Recommends Following Accessories CAT. noProtector Open, only Motor wd! notBox TooTrouble Shooting -- Motor RemedyLOW Voltage Parts List Supplied WithHardware for Mounting Tool & Motor Craftsman Belt and Disc Sander Model no .225900 & 113,225931 Housing, Disc 47222Repair parts Key Part DescriptionWith Plug Black Wire to Terminal T1 Green Wire to Green Screw Outlet Before ProceedingRepair parts Switch MountingDoes Not Include Key No, 3. Order Separately If Required Page BEL T and Disc Sander