Craftsman 113.225900 manual Surface Finishing on Abrasive Belt, Before freeing any jammed material

Page 20

operaho " rt

Plan the way you will hold the workpiece from start to finish Avoid awkward operations and hand positions Where a sud- den s p cou d cause fingers or hand to move into a sanding surface, Keep fingers away from where the belt goes into the dust trap-

DON'T OVERREACH, Keep good footing and balance,

Keep your face and body to one side. out of line with a pos-

sible throwback.

WHENEVER SANDER IS RUNNING-

WARNING: Don't let familiarity (gained from frequent use of

your belt and disc sander) cause a careless mistake. A care- less fraction of a second is enough to cause a severe injury.

Before starting your cut, watch the sander while it runs. if it makes an unfamiliar noise or vibratesa lot, stop immediately, Turn the sander off, Unplug the sander, Do not restart until

finding and correcting the problem.

Make sure the sanding disc turns counterclockwise before using the sunder,

KEEP CHILDREN AWAY. Keep aU visitors a safe distance from the sander. Make sure bystanaers are clear of the sunder and workpiece.

DON'T FORCE TOOL. it will do the job better and safer at its

designated rate. Press the workoiece against the sanding

material only hard enough to let it sand without bogging down or binding.

Before freeing any jammed material:

Turn switch "OFF,"

Unplug the sanaer.

Wait for all mov=ng parts to stop.

-fo avoid throwback of the workpiece, use workpiece supports for all flat surface sanding.

BEFORE LEAVING THE SANDER:

Wait for all moving parts to stop.

Make workshop child-Drool. Lock the shoD. Disconnect

_naster switches. Remove the vetlow switch key. Store ii

away from children and others not qualified to use the tool,

SURFACE FINISHING ON THE

ABRASIVE BELT.

\

FLATSURFACES

\

Hold the work piece firmly with both hands, keeping

fingers away from the abrasive belt.

Keep the end butted against the backstop and move the work evenly across the abrasive belt. Use extra caution

when finishing very thin pieces.

For finishing long pieces, remove the backstop.

Apply only enough pressure to allow the abrasive belt

to remove material. If the abras=ve belt stalls and the belt pulleys slip while applying moderate pressure to the workpiece, the abrasive belt reouires more tension.

END FINISHING ON THE

ABRASIVE BELT,

I1 is more convient to finish the ends of long work- pieces with the abrasive belt in a vertical position.

Move the work evenly across the abrasive belt. For accuracy use a miter guage.

The table may be tilted for beveled work.

See Getting To Know Your Finishing Machine section for adjusting the abrasive belt table and the work table,

/

/

2O

Image 20
Contents Belt and Disc Legs and MotorGeneral safety instructions Power toolsSander Before Using the SanderBefore Each USE At a time Whenever Sander is RunningPlan your work Grounded /n Ul OUTLETs Connecting to Power Source OutletProperly Contents Unpacking and checkingFollowing parts are included with Model AssernbJyHAROWABEFORMOUNTINGTOOL& Motor Mounting Belt and Disc Sander on Craftsman Steel LEG SET Catalog noInstalling Sanding Disc and Dust Trap AssemblyWrench Belt Table LockingAssembly Flat SpotDisc Dust Trap Flat Head Screws TrapTOP Right Hand Screw Dust Trap Cover TWO HolesClips 10-32 X 1/2Assembly ON-OFF SwitchInsert key into switch Place the bolt onto the motor pulley by rotating the pulleyFind plastic cable hanger from among the loose parts Power Cord Motor CordCable Installing Work Table Directional ARROW\ Be LT Adjusting SCR EWSPull Wrenches in this Direction to Apply Tension Belt Locking ScrewInstalling Belt Dust Trap Belt Leftmoving To RightBelt Locking Screw Drive PulleyInstalling Backstop AssembWyGetting to know your belt and disc sander ANY Aojustm EntsBelt Adjusting Screw ONE on Each Side From Disc Positioning Lock Screw Stop Tilt Lock NUTRaise the table and loosen the lock nut using a 7/16 wrench Ge ng to know you r belt and disc sanderPlace. It is locked uing the 1/2 wrench Lock NUtBefore Each USE Before Using the SanderBasic operation Surface Finishing on Abrasive Belt Before freeing any jammed materialFor finishing long pieces, remove the backstop END Finishing on Abrasive BeltCurved Edges Motor Maintenance Lubrication Sears Recommends Following AccessoriesCausing thebelt to sli CAT. noMotor wd! not BoxProtector Open, only TooLOW Voltage Trouble Shooting -- MotorRemedy Hardware for Mounting Tool & Motor Parts ListSupplied With Craftsman Belt and Disc Sander Model no .225900 & 113,225931 Housing, Disc 47222With Plug Repair partsKey Part Description Black Wire to Terminal T1 Green Wire to Green Screw Outlet Before ProceedingDoes Not Include Key No, 3. Order Separately If Required Repair partsSwitch Mounting Page BEL T and Disc Sander