Craftsman 113.225909, 113.225931, 113.225900 Assembly, Flat Spot, Disc Dust Trap Flat Head Screws

Page 10

assembly

B. Find five 378" Pan Head Self-Treading screws from

among the loose parts.

7.Place Disc Dust Trap on your workbench and screw m

five Pan Head "Thread Cutting Screws," 3/8" long. Screw them in all the way.

NOTE:

The

holes

in the Trap

are not

threaded but the

screws

are

"Thread

Cutting

Screws"

and will cut a

thread

as

they

are

tightened.

 

 

R. Find four Flat Head Machine Screws 1-¾" long from among the loose _arts

9.Attach the Disc Dos1 Trap with four flat head screws !-¾"long.

10.There is a flat spot on the shaft near the end. Rotate the shaft so that the flat spot is facing up.

11 Place the disc on the shaft so that the set screw ts facmc up. Position the disc so that it is approx, 1/16 rich outward from the edge of the dust trap.

12 Insert the long end of me 532" setscrew wrench through me hole in the disc housmg and mto the

setscrew n the disc. Make sure setscrew _s aligned with "F ]at" on shaft.

NOTE: After several hours of operation, check for ooseness of setscrew and ret_gh[er

13.Make certain that the metal disc is free of oil and grease then peel the backing from the 9" abrasive disc and affix to the sanding disc.

DISC DUST TRAP

FLAT HEAD SCREWS

1 3/4" LONG

FLAT SPOT

/ONSHAFT

/

/

/

/ / /

5/32INCH

/--SETSCREW

/WRENCH

TRAP

\ \

\

10

Image 10
Contents Belt and Disc Legs and MotorGeneral safety instructions Power toolsBefore Each USE Before Using the SanderSander Plan your work Whenever Sander is RunningAt a time Properly Connecting to Power Source OutletGrounded /n Ul OUTLETs Contents Unpacking and checkingHAROWABEFORMOUNTINGTOOL& Motor AssernbJyFollowing parts are included with Model Mounting Belt and Disc Sander on Craftsman Steel LEG SET Catalog noWrench Installing Sanding Disc and Dust TrapAssembly Belt Table LockingDisc Dust Trap Flat Head Screws AssemblyFlat Spot TrapClips TOP Right Hand Screw Dust Trap CoverTWO Holes 10-32 X 1/2Insert key into switch AssemblyON-OFF Switch Place the bolt onto the motor pulley by rotating the pulleyCable Power Cord Motor CordFind plastic cable hanger from among the loose parts Pull Wrenches in this Direction to Apply Tension Installing Work TableDirectional ARROW\ Be LT Adjusting SCR EWS Belt Locking ScrewBelt Locking Screw Drive Installing Belt Dust TrapBelt Leftmoving To Right PulleyGetting to know your belt and disc sander Installing BackstopAssembWy ANY Aojustm EntsBelt Adjusting Screw ONE on Each Side From Disc Positioning Lock Screw Stop Tilt Lock NUTPlace. It is locked uing the 1/2 wrench Raise the table and loosen the lock nut using a 7/16 wrenchGe ng to know you r belt and disc sander Lock NUtBasic operation Before Using the SanderBefore Each USE For finishing long pieces, remove the backstop Surface Finishing on Abrasive BeltBefore freeing any jammed material END Finishing on Abrasive BeltCurved Edges Causing thebelt to sli Motor Maintenance LubricationSears Recommends Following Accessories CAT. noProtector Open, only Motor wd! notBox TooRemedy Trouble Shooting -- MotorLOW Voltage Supplied With Parts ListHardware for Mounting Tool & Motor Craftsman Belt and Disc Sander Model no .225900 & 113,225931 Housing, Disc 47222Key Part Description Repair partsWith Plug Black Wire to Terminal T1 Green Wire to Green Screw Outlet Before ProceedingSwitch Mounting Repair partsDoes Not Include Key No, 3. Order Separately If Required Page BEL T and Disc Sander