Craftsman 113.225931, 113.225909, 113.225900 manual Repair parts, Switch Mounting

Page 30

repair parts

_ _i _

CRAFTSMAN BELT AND DISC SANDER MODEL NO. 113.225900 & 113.225931

78

S 6

34

FIGURE 4 PARTS LIST

ON\OFF POWER OUTLET 60382 AND

 

 

MOUNTING

BRACKET

Key

 

 

 

 

No.

No,

Description

J

 

 

 

 

--

60382

Oa/Off

Power

Outlet

1

60375

Cord,

Molded

 

2

60378

Heusing, Switch

 

3

9-22255

t-Key, Switch

 

4

60374

 

Switch,

Locking

 

5

60376

Cever,

Switch

 

6

448007

Screw,

Pan Hd. No. 6 x 3/4

7

68066

Bracket,

Switch

Mounting

 

 

8STD600803 *Screw, Pan Hd. Plastite No. 8 x 3&/8

*Standard Hardware item - May be Purchased Locally.

Does Not Include Key No, 3. Order Separately If Required.

TStock Item--May be secured through the Hardware Deeartment of most Sears Retail Stores or Catatog Order Houses.

NOTE: Shipping and handling charges for standard hardware items (identified by *l such as nuts. screws, washers, etc., make

buying these items by mait uCeconomicaL To avoid shipping and handling charges, you may obtain most of these locally

30

Image 30
Contents Belt and Disc Legs and MotorGeneral safety instructions Power toolsBefore Using the Sander Before Each USESander Whenever Sander is Running Plan your workAt a time Connecting to Power Source Outlet ProperlyGrounded /n Ul OUTLETs Contents Unpacking and checkingAssernbJy HAROWABEFORMOUNTINGTOOL& MotorFollowing parts are included with Model Mounting Belt and Disc Sander on Craftsman Steel LEG SET Catalog noWrench Installing Sanding Disc and Dust TrapAssembly Belt Table LockingDisc Dust Trap Flat Head Screws AssemblyFlat Spot TrapClips TOP Right Hand Screw Dust Trap CoverTWO Holes 10-32 X 1/2Insert key into switch AssemblyON-OFF Switch Place the bolt onto the motor pulley by rotating the pulleyPower Cord Motor Cord CableFind plastic cable hanger from among the loose parts Pull Wrenches in this Direction to Apply Tension Installing Work TableDirectional ARROW\ Be LT Adjusting SCR EWS Belt Locking ScrewBelt Locking Screw Drive Installing Belt Dust TrapBelt Leftmoving To Right PulleyGetting to know your belt and disc sander Installing BackstopAssembWy ANY Aojustm EntsBelt Adjusting Screw ONE on Each Side From Disc Positioning Lock Screw Stop Tilt Lock NUTPlace. It is locked uing the 1/2 wrench Raise the table and loosen the lock nut using a 7/16 wrenchGe ng to know you r belt and disc sander Lock NUtBefore Using the Sander Basic operationBefore Each USE For finishing long pieces, remove the backstop Surface Finishing on Abrasive BeltBefore freeing any jammed material END Finishing on Abrasive BeltCurved Edges Causing thebelt to sli Motor Maintenance LubricationSears Recommends Following Accessories CAT. noProtector Open, only Motor wd! notBox TooTrouble Shooting -- Motor RemedyLOW Voltage Parts List Supplied WithHardware for Mounting Tool & Motor Craftsman Belt and Disc Sander Model no .225900 & 113,225931 Housing, Disc 47222Repair parts Key Part DescriptionWith Plug Black Wire to Terminal T1 Green Wire to Green Screw Outlet Before ProceedingRepair parts Switch MountingDoes Not Include Key No, 3. Order Separately If Required Page BEL T and Disc Sander