Craftsman 113.225900, 113.225931, 113.225909 manual BEL T and Disc Sander

Page 32

SERVICE

MODEL NO. 113.225900

BELT AND DISC

SANDER ONLY

MODEL NO.

333.225931

BELT AND DISC

SANDER/WITH

LEGS AND MOTOR

HOW TO ORDER

REPAIR PARTS

BEL T AND DISC SANDER

Now that you have purchased your Belt & Disc Sander should a need ever exist for repair parts or service, simply contact any Sears Service Center and most Sears, Roebuck and Co. stores. Be sure to provide a!l pertinent facts when you call or visit.

The model number of your Belt and Disc Sander will be found

on a plate attached to your sander at the right-hand side of the base.

WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE

FOLLOWING	INFORMATION:
PART NUMBER		PART	DESCRIPTION
MODEL NUMBER		NAME	OF ITEM
113.225900	OR	Belt And Disc Sander
113.225931

All parts listed may be ordered from any Sears Service Center and most Sears stores. If the parts you need are not stocked locally, your order wilt be electronically transmitted to a Sears Repair Parts Distribution Center for handling.

Sold by SEARS, ROEBUCKAND CO., Chicago, IL. 60684 U.S.A.

Part No. 68073

Form No. SP4928-2

Printed in U.S,#

Image 32

Contents Belt and Disc Legs and MotorGeneral safety instructions Power toolsSander Before Using the SanderBefore Each USE At a time Whenever Sander is RunningPlan your work Grounded /n Ul OUTLETs Connecting to Power Source OutletProperly Contents Unpacking and checkingFollowing parts are included with Model AssernbJyHAROWABEFORMOUNTINGTOOL& Motor Mounting Belt and Disc Sander on Craftsman Steel LEG SET Catalog noInstalling Sanding Disc and Dust Trap AssemblyWrench Belt Table LockingAssembly Flat SpotDisc Dust Trap Flat Head Screws TrapTOP Right Hand Screw Dust Trap Cover TWO HolesClips 10-32 X 1/2Assembly ON-OFF SwitchInsert key into switch Place the bolt onto the motor pulley by rotating the pulleyFind plastic cable hanger from among the loose parts Power Cord Motor CordCable Installing Work Table Directional ARROW\ Be LT Adjusting SCR EWSPull Wrenches in this Direction to Apply Tension Belt Locking ScrewInstalling Belt Dust Trap Belt Leftmoving To RightBelt Locking Screw Drive PulleyInstalling Backstop AssembWyGetting to know your belt and disc sander ANY Aojustm EntsBelt Adjusting Screw ONE on Each Side From Disc Positioning Lock Screw Stop Tilt Lock NUTRaise the table and loosen the lock nut using a 7/16 wrench Ge ng to know you r belt and disc sanderPlace. It is locked uing the 1/2 wrench Lock NUtBefore Each USE Before Using the SanderBasic operation Surface Finishing on Abrasive Belt Before freeing any jammed materialFor finishing long pieces, remove the backstop END Finishing on Abrasive BeltCurved Edges Motor Maintenance Lubrication Sears Recommends Following AccessoriesCausing thebelt to sli CAT. noMotor wd! not BoxProtector Open, only TooLOW Voltage Trouble Shooting -- MotorRemedy Hardware for Mounting Tool & Motor Parts ListSupplied With Craftsman Belt and Disc Sander Model no .225900 & 113,225931 Housing, Disc 47222With Plug Repair partsKey Part Description Black Wire to Terminal T1 Green Wire to Green Screw Outlet Before ProceedingDoes Not Include Key No, 3. Order Separately If Required Repair partsSwitch Mounting Page BEL T and Disc Sander