Craftsman 113.225900 manual Mounting Belt and Disc Sander on Craftsman Steel LEG SET, Catalog no

Page 8

1. Assemble the two (2) End Stiffeners and the two 2

Side

Stiffeners

using four

(4)

1/4-20

Truss

head

screws. The End Stiffeners are placed On top of each

Side

Stiffener

as shown.

Insert

screws

through

the

END STIFFENER

SCREW _ 1

STIFFENERS,DE

LOCKWASHER

HEX NUT

LOCKWASHER

ST,FFEN R

SIDE STIFFENER

 

9/32 inch diameter holes and finger tighten 1/4-20

 

nutS.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2.

Attach

 

the

four

(4)

legs to the side and End

Stiffener

 

 

using 1/4-20 screws, Iockwashers

and

nuts

as shown.

3.

Remove

 

the

 

four

(41 Truss

head

screws

which

were

 

assembled in Paragraph No. One. Place the two (2

 

Support

 

Channels

as shown,

in position

 

align holes

in

 

supports

 

 

with

holes

in

the

Stiffeners,

 

replace

 

Iockwashers

 

and nuts, Tighten all nuts using 7/16

 

 

wrench.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4.

Assemble

the

motor

support

to steel

legs with

1/4-20

 

screws

and

nuts.

Motor

support

can

be

mounted

to

 

either end of stand. Tignlen nuts

 

 

 

 

 

 

5.

Install

leveling

feet

as shown.

To

level

Leg Set,

loosen

 

 

\

HEX NUT

_e

_ CH/%NNEL

 

.r

_- _

SUPPORT

 

_

k

_.

LEG

\

CHANNEL SUPPORT

MOTOR SUPPORT

LEG

SCREW

nut

on

inside of

leg

and

turn

nut

on outside to raise

or lower feet. Adjust alt four levelers, if necessary,

and

then

tighten

nuts

on

inside

of

leg.

NOTE: These levelers are not intended for height adjustment.

WHEN INSTALLING OR MOVING THE SANDER.

AVOID DANGEROUS ENVIRONMENT, Use the sander n a dry, indoor place protected from rain. Keen work area well lighted.

Place the sander so neither the user nor bystanders are forced to stand in line with the abrasive belt or d sc.

To avoid injury from unexpected sandel movement:

=Put the sander on a firm level surface where there is plenty

of room for handling and properly supporting the workpiece.

- Support the sander so it does not rock.

,,Bolt the sander tothe floor or work surfaceif it tends to slip, walk. or slide during normal use.

To avoid back injury, get help or use recommended casters when you need to move the sander. Always get help if you need to lift the sander.

NEVER STAND ON TOOL. Serious injury could occur if the too] tips or you accidentally hit the cutting tool, Do not store

anything above or near the toot where anyone might stand on the tool to reach them.

/

SCREW

/NUT

LOCKWASHER

#

MOTOR MOUNT

BRACKET

THISSIDE

MOUNTING BELT AND DISC SANDER ON

CRAFTSMAN STEEL LEG SET.

CATALOG NO. 9-22236

NOTE: Forillustrative purposes, the Belt and Disc Sander is shown mounted on the Craftsman Catalog No. 9-22236 Steel Leg Set. This Leg Set is included with Model No. 113.225931.

0 C

OOc

o°o

o o

___coc

Image 8
Contents Belt and Disc Legs and MotorGeneral safety instructions Power toolsSander Before Using the SanderBefore Each USE At a time Whenever Sander is RunningPlan your work Grounded /n Ul OUTLETs Connecting to Power Source OutletProperly Contents Unpacking and checkingFollowing parts are included with Model AssernbJyHAROWABEFORMOUNTINGTOOL& Motor Mounting Belt and Disc Sander on Craftsman Steel LEG SET Catalog noInstalling Sanding Disc and Dust Trap AssemblyWrench Belt Table LockingAssembly Flat SpotDisc Dust Trap Flat Head Screws TrapTOP Right Hand Screw Dust Trap Cover TWO HolesClips 10-32 X 1/2Assembly ON-OFF SwitchInsert key into switch Place the bolt onto the motor pulley by rotating the pulleyFind plastic cable hanger from among the loose parts Power Cord Motor CordCable Installing Work Table Directional ARROW\ Be LT Adjusting SCR EWSPull Wrenches in this Direction to Apply Tension Belt Locking ScrewInstalling Belt Dust Trap Belt Leftmoving To RightBelt Locking Screw Drive PulleyInstalling Backstop AssembWyGetting to know your belt and disc sander ANY Aojustm EntsBelt Adjusting Screw ONE on Each Side From Disc Positioning Lock Screw Stop Tilt Lock NUTRaise the table and loosen the lock nut using a 7/16 wrench Ge ng to know you r belt and disc sanderPlace. It is locked uing the 1/2 wrench Lock NUtBefore Each USE Before Using the SanderBasic operation Surface Finishing on Abrasive Belt Before freeing any jammed materialFor finishing long pieces, remove the backstop END Finishing on Abrasive BeltCurved Edges Motor Maintenance Lubrication Sears Recommends Following AccessoriesCausing thebelt to sli CAT. noMotor wd! not BoxProtector Open, only TooLOW Voltage Trouble Shooting -- MotorRemedy Hardware for Mounting Tool & Motor Parts ListSupplied With Craftsman Belt and Disc Sander Model no .225900 & 113,225931 Housing, Disc 47222With Plug Repair partsKey Part Description Black Wire to Terminal T1 Green Wire to Green Screw Outlet Before ProceedingDoes Not Include Key No, 3. Order Separately If Required Repair partsSwitch Mounting Page BEL T and Disc Sander