Grizzly w1702 instruction manual Handle

Page 41

REF	PART #	DESCRIPTION

101	X1702101	HANDLE
102	X1702102	HANDWHEEL
103	XPB09	HEX BOLT 5⁄16"-18 x 1⁄2"
104	XPSS15	SETSCREW 3⁄8"-16 x 3⁄8"
105	XPSS08	SETSCREW 5⁄16"-18 x 1⁄2"
106	X1702106	COLLAR
107	XPSB07	CAP SCREW 5⁄16"-18 x 3⁄4"
108	X1702108	SHAFT MOUNT
109	X1702109	BUSHING
111	X1702111	WORM SHAFT
113	XP51103	BEARING
114	X1702114	GIB
115	X1702115	ELEVATION HOUSING
116	XPN02	HEX NUT 5⁄16"-18
118	XPB72	HEX BOLT 1⁄2"-13 x 2"
119	XPLW07	LOCK WASHER 1⁄2"
120	XPLN07	LOCK NUT 5⁄8"-11
121	X1702121	GEAR 25T
122	XPK06M	KEY 5 x 5 x 10mm
127	XPW07	FLAT WASHER 5⁄16"
128	X1702128	HAND KNOB 3⁄8"-16
129	XPB25	HEX BOLT 3⁄8"-16 x 13⁄4"
131	XPB19	HEX BOLT 1⁄4"-20 x 1⁄2"
132	XPW06	FLAT WASHER 1⁄4"
133	X1702133	“L” BRACKET

REF	PART #	DESCRIPTION

134	W1702134	POINTER
135	XPW07	FLAT WASHER 5⁄16"
136	X1702036	ELEVATION LEAD SCREW
137	X1702137	CARTRIDGE SLIDE
138	XPB15	HEX BOLT 5⁄16"-18 x 3⁄8"
139	X1702146	V-BELT 7m690
141	XPB22	HEX BOLT 5⁄16"-18 x 13⁄4"
142	XPW07	FLAT WASHER 5⁄16"
143	XPLW01	LOCK WASHER 5⁄16"
144	XPK06M	KEY 5 x 5 x 10
145	X1702145-2	CAPACITOR COVER
147	X1702147	MOTOR PULLEY
148	XPW01	FLAT WASHER 1⁄2"
149	XPLW07	LOCK WASHER 1⁄2"
150	XPSS02	SETSCREW 5⁄16"-18 x 3⁄8"
151	X1702151	MOTOR MOUNT PLATE
152	X1702152	MOTOR 3 HP
153	X1702145-3	WIRE BOX COVER
154	X1702145-4	MOTOR FAN
155	X1702145-5	MOTOR FAN COVER
156	XPSS20	SETSCREW 5⁄16"-18 x 11⁄2"
157	XPB55	HEX BOLT 1⁄2" - 13 x 11⁄2"
158	X1702137	CABLE CLAMPS
159	X1702152-1	START CAPACITOR
161	XPW01	FLAT WASHER 1⁄2"

-39-

PARTS

Image 41

Contents HP Shaper Page Contents About Your New Shaper Woodstock Service and SupportIntroduction Specifications Warranty and ReturnsStandard Safety Instructions SafetySafety Additional Safety Instructions for Shapers Use a Shop FOX Featherboard as Avoiding Potential Injuries220V Operation ElectricalExtension Cords GroundingInventory AssemblyUnpacking Beginning Initial CleaningShop Preparation Dust CollectionAuxiliary Guard Safety GuardFence Facing To install the crank handle, do these steps To install the hold-downs, do these stepsHold-Downs HandwheelUnplug the Shaper SpindleThreading drawbar nut onto drawbar Fence Positioning AdjustmentsTo adjust the fence, do these steps Fence Alignment Table Inserts To adjust the table inserts, do these stepsTo align the pulleys, do these steps Pulley AlignmentTo change the spindle RPM, do these steps Spindle RPMChoose Spindle RPM To check the spindle slide-to-gib clearance, do these steps Spindle Slide and GibStart Up OperationsCutter Direction Forward and reverse switchChoose Cutter Profile and Cutter Cutter InstallationChoose Cutter Height and Spindle Size Choose Spindle and Cutter RPMPlace the spindle washer onto the spindle as shown in Figure To set the spindle height, do these steps Setting Spindle HeightStraight Shaping Operations Rub Collars There are three set up positions for rub collarsStarting pin operation Guard not shown for clarity Freehand ShapingTo make a template, do these steps Pattern ShapingGeneral MaintenanceTable and Base LubricationTroubleshooting Closure Model W1702 220V Wiring Diagram Parts Stand Parts Handle Parts XPR15M Parts XPW02 Lock Washer 3⁄8 Parts Miter Gauge Body HOLD-DOWN BAR Shaper Accessories Shaper Accessories Your Notes Your Notes Warranty Card BOX BELLINGHAM, WA