Grizzly w1702 instruction manual Assembly, Unpacking, Inventory

Page 11

ASSEMBLY

Unpacking

GET lifting assistance when removing the shaper from the box. At 352 pounds, the Model W1702 Shaper is a heavy load.

1

Figure 9. Shaper unit.


			25		23
			25		2
					2
					14
		19			28
		19			3
			9	8	3
	10		9	8	7
	10		13		17
			13	5	4
			6	5	4
		15	11		16
	21		20
			12		18
	26	27	22		18
			24

Figure 10. Layout of components.

The Model W1702 is carefully packed. However, if it is damaged or is missing any parts, please contact Woodstock International Service and Support at 1-360-734-3482 or send e-mail to: tech-support@shopfox.biz.

Inventory

Layout and inventory the shipped parts to familiarize yourself with your Model W1702 Shaper. See Figures 9 and 10. Familiarizing yourself will help with the installation process, set-up, and machine operation.

Item		Qty.
1.	Shaper Unit	1
2.	Miter Gauge	1
3.	Handle	1
4.	1⁄2" Spindle	1
5.	3⁄4" Spindle	1
6.	1" Spindle	1
7.	1⁄2" Spindle Nut	2
8.	3⁄4" Spindle Nut	2
9.	1" Spindle Nut	2
10.	Spacer Bag	1
11.	Draw Bar and Nut	1
12.	Spindle Wrench Set	2
13.	Safety Guard	1
14.	Safety Guard Shaft	1
15.	Starting Pins	3
16.	Hold-Downs	4
17.	Hold-Down Bars	2
18.	Hold-Down Brackets	4
19.	Fence Faces	2
20.	Washers	6
21.	Hardware Bag	1
	• Set Screw 1⁄4" - 20 x 3⁄8"	4
	• Hex Nut 5⁄16" - 18	2
	• Flat Hd Screw 5⁄16" - 18 x 1⁄4"	2
	• Flat Washer 5⁄16"	2
22.	Guard Mounting Bar	1
23.	Guard Holding Bracket	1
24.	Guard Support	1
25.	Fence Housing Assembly	1
26.	Fence Housing Mounting Cap Screws	3
27.	Shaft Holder Mounting Hex Bolts	2
28.	Shaft Holder	1

ASSEMBLY

-9-

Image 11

Contents HP Shaper Page Contents About Your New Shaper Woodstock Service and SupportIntroduction Specifications Warranty and ReturnsStandard Safety Instructions SafetySafety Additional Safety Instructions for Shapers Use a Shop FOX Featherboard as Avoiding Potential InjuriesGrounding Electrical220V Operation Extension CordsInventory AssemblyUnpacking Beginning Initial CleaningShop Preparation Dust CollectionAuxiliary Guard Safety GuardFence Facing Handwheel To install the hold-downs, do these stepsTo install the crank handle, do these steps Hold-DownsUnplug the Shaper SpindleThreading drawbar nut onto drawbar Fence Positioning AdjustmentsTo adjust the fence, do these steps Fence Alignment Table Inserts To adjust the table inserts, do these stepsTo align the pulleys, do these steps Pulley AlignmentTo change the spindle RPM, do these steps Spindle RPMChoose Spindle RPM To check the spindle slide-to-gib clearance, do these steps Spindle Slide and GibStart Up OperationsCutter Direction Forward and reverse switchChoose Spindle and Cutter RPM Cutter InstallationChoose Cutter Profile and Cutter Choose Cutter Height and Spindle SizePlace the spindle washer onto the spindle as shown in Figure To set the spindle height, do these steps Setting Spindle HeightStraight Shaping Operations Rub Collars There are three set up positions for rub collarsStarting pin operation Guard not shown for clarity Freehand ShapingTo make a template, do these steps Pattern ShapingLubrication MaintenanceGeneral Table and BaseTroubleshooting Closure Model W1702 220V Wiring Diagram Parts Stand Parts Handle Parts XPR15M Parts XPW02 Lock Washer 3⁄8 Parts Miter Gauge Body HOLD-DOWN BAR Shaper Accessories Shaper Accessories Your Notes Your Notes Warranty Card BOX BELLINGHAM, WA