Grizzly w1702 instruction manual Fence Facing, Safety Guard, Auxiliary Guard

Page 14

ASSEMBLY

Fence Facing

Fence facing can be custom made for special needs—for example, mounting a hold-down roller systems like the SHOP FOX® Model W1105 Green BOARD BUDDIES®.

To install the fence facing, do these steps:

1.Using 1⁄4"-20 x 5⁄8" Countersunk Phillips® head screws, 1⁄4" washers, and 1⁄4"-20 T-nuts; install each fence facing to the fence mount brackets as shown in Figure 12.

2.For custom fence facing, make sure the screw heads are countersunk completely below the surface of the fence face.

Safety Guard

Always use a safety guard whenever possible. The safety guard improve shaping safety.

To install the safety guard, do these steps:

1.Connect the extension bar to the safety guard with two 1⁄4 "-20 x 3⁄8 " bolts and the

1⁄4 " hex nuts.

2.Thread the support into the main fence housing. See Figure 13.

3.Position the extension bar and safety guard on the main fence housing and install the T-lock handle. See Figure 13.

Auxiliary Guard

Certain freehand shaping procedures require you to attach auxiliary wooden guards to the safety guard assembly as shown in Figure 14.

To make and install auxiliary wooden guards, do these steps:

1.From 1⁄2" wood stock, measure and cut one front wooden guard at 6" long, and two side guards at 21⁄2" long.

NOTE: Guard height depends on the thickness of the material you are shaping. If using a template attached to the workpiece, be sure to include template height for the overall height.

2.Secure the auxiliary wooden guards to the lip of the guard assembly with six #10 wood screws.

-12-

T-nut

Figure 12. Installing fence facing.

 

T-lock

 

Handle

Safety

Extension

Bar

Guard

 

 

Support

 

Main

 

Fence

 

Housing

Figure 13. Threading lock handle onto the

guard assembly.

Guard Assembly

#10 Wood Screws

Auxiliary Wooden Guard

Figure 14. Auxiliary wooden guards.

Page 13 Page 15
Image 14
Page 13 Page 15
Contents HP Shaper Page Contents About Your New Shaper Woodstock Service and SupportIntroduction Warranty and Returns SpecificationsSafety Standard Safety InstructionsSafety Additional Safety Instructions for Shapers Avoiding Potential Injuries Use a Shop FOX Featherboard asExtension Cords Electrical220V Operation GroundingInventory AssemblyUnpacking Initial Cleaning BeginningDust Collection Shop PreparationAuxiliary Guard Safety GuardFence Facing Hold-Downs To install the hold-downs, do these stepsTo install the crank handle, do these steps HandwheelSpindle Unplug the ShaperThreading drawbar nut onto drawbar Fence Positioning AdjustmentsTo adjust the fence, do these steps Fence Alignment To adjust the table inserts, do these steps Table InsertsPulley Alignment To align the pulleys, do these stepsTo change the spindle RPM, do these steps Spindle RPMChoose Spindle RPM Spindle Slide and Gib To check the spindle slide-to-gib clearance, do these stepsOperations Start UpForward and reverse switch Cutter DirectionChoose Cutter Height and Spindle Size Cutter InstallationChoose Cutter Profile and Cutter Choose Spindle and Cutter RPMPlace the spindle washer onto the spindle as shown in Figure Setting Spindle Height To set the spindle height, do these stepsStraight Shaping Operations There are three set up positions for rub collars Rub CollarsFreehand Shaping Starting pin operation Guard not shown for clarityPattern Shaping To make a template, do these stepsTable and Base MaintenanceGeneral LubricationTroubleshooting Closure Model W1702 220V Wiring Diagram Parts Stand Parts Handle Parts XPR15M Parts XPW02 Lock Washer 3⁄8 Parts Miter Gauge Body HOLD-DOWN BAR Shaper Accessories Shaper Accessories Your Notes Your Notes Warranty Card BOX BELLINGHAM, WA
Top Page Image Contents