Skil 9205 manual Using the Saw, Blade Storage Compartment, Sawing Tips, Wrong Right

Page 8

SM 2610938738 03-06 3/10/06 9:28 AM Page 8

blade protrusion beyond the end of the footplate when cutting into large diameter pipe FIG. 4 or into walls.

To adjust the footplate position depth, simply loosen the two screws in insulated rubber boot with wrench provided, slide and move the footplate to the desired position and securely tighten the screw with the wrench provided (Fig. 4).

BLADE STORAGE COMPARTMENT

Your tool is equipped with a blade storage FIG. 5 compartment (Fig. 5) on the backside of your

saw. To remove, push down on tab and slide in direction of arrow. Be sure storage compartment is closed to prevent blades from falling out.

BLADE STORAGE TAB

BLADE STORAGE COMPARTMENT

Using the Saw

1. Securely clamp the work.

2. Mark the line of cut and grasp the tool with one hand on the handle and the other placed on the insulated rubber boot over the front housing.

!Always hold the saw by the WARNING insulated boot on the front housing. If you saw into a blind area where live wiring exists, you may be shocked or

electrocuted.

3. Keep the saw footplate firmly against the work to minimize counter-force (jumping) and vibration.

4. Squeeze the trigger to start the tool. Let the saw reach full speed before starting the cut. Guide the saw so that the blade will move along the marked line.

SAWING TIPS

Following a few simple tips will reduce the wear on the workpiece, the tool and the operator.

1. Blades cut on the draw or back stroke. On fine work, such as paneling, fiberglass, etc., place the good side of workpiece facing down.

2. Use the correct saw blade for the material being cut and keep extra blades on hand to

use when others become dull. Replace cracked or bent blades immediately.

3. Select the footplate projection settings, as well as the appropriate cutting speed.

4. To reduce the risk of injury, be sure the blade always extends beyond the footplate and work throughout the stroke. Blades may shatter if the front on the blade hits the work and/or the footplate.

5. When cutting metal:

WRONGRIGHT

- Apply a lubricant for easier, smoother, faster cutting and longer blade life.

- For non-ferrous metals, aluminum, bronze or brass, use a stick wax on the blade.

-8-

Image 8
Contents Leer antes de usar For English Version Version françaiseCall Toll Free for See Voir Ver la páginaElectrical safety General Safety RulesPersonal safety Service Safety Rules for Reciprocating SawsPower tool use and care SM 2610938738 03-06 3/10/06 928 AM Symbols Functional Description and Specifications Disconnect the plug from the power source before making anyReciprocating Saw Measures reduce the risk of starting the tool accidentallyAssembly Operating InstructionsUsing the Saw Blade Storage CompartmentSawing Tips Wrong RightPocket Cuts POCKET/PLUNGE Cuts Maintenance AccessoriesCleaning Tool LubricationConsignes générales de sécurité Sécurité du lieu de travailSécurité électrique Sécurité personnelleEntretien Règles de sécurité concernant les scies va-et-vientUtilisation et entretien des outils Électroportatifs Le plomb provenant des peintures à base de plomb Symboles Description fonctionnelle et spécifications Scies va-et-vientApprêt de la scie AssemblageConsignes de fonctionnement Utilisation de la scie Compartiment DE Rangement DE LameConseils Pour LE Sciage NonouiRemarques Mode d’emploi risque de présenter un dangerSciages D’ÉVIDEMENTS/EN Plongée Accessoires EntretienLubrification DE L’OUTIL Balais OU CharbonsNormas generales de seguridad Seguridad del área de trabajoSeguridad eléctrica Seguridad personalServicio de ajustes y reparaciones Normas de seguridad para sierras alternativasMecánicas SM 2610938738 03-06 3/10/06 928 AM Símbolos Riesgo de arrancar la herramienta accidentalmente Descripción funcional y especificacionesSierras alternativas Preparacion de la sierra EnsamblajeInstrucciones de funcionamiento Incorrectocorrecto Uso de la sierraConsejos Para Aserrar Puede crear un peligro NotasNo haga cortes por penetración en superficies metálicas Mantenimiento AccesoriosServicio LimpiezaSM 2610938738 03-06 3/10/06 928 AM Remarques Notas SM 2610938738 03-06 3/10/06 928 AM