Bosch Power Tools CCS180K, CCS180B manual Cutting MASONRy/METAL, Plunge Cuts, Wrong Right

Page 12
! WARNING

BM 2610034442 03-14_CCS180 3/27/14 12:25 PM Page 12

CUTTING MASONRy/METAL

This tool is not recommended for usage with metal or masonry cut-off wheels.

!WARNING Do not cut metal or masonry with this circular

saw. The dust from metal or masonry cutting will cause the lower guard to become sluggish and may not close fully and quickly after cutting these materials.

Do not cut with abrasive ! WARNING wheels around flammable

materials or environments. Abrasive cutting may produce sparks that could ignite flammable materials and cause explosion hazards.

Do not use Wet Diamond cutting off wheel or water feed devices with this circular saw.

Masonry cutting waste will enter the lower guard system, harden and cause the guard to become inoperable. Use of water in masonry cutting applications with an electric circular saw will cause electric shock hazards.

PLUNGE CUTS

Disconnect battery pack from tool before making adjustments. Set depth adjustment according to material to be cut. Tilt saw forward with cutting guide notch lined up with the line you’ve drawn. Raise the lower guard, using lift lever and hold the saw by the front and rear handles (Fig. 10).

With the blade just clearing the material to be cut, start the motor. Gradually lower the back end of saw using the front end of the foot as the hinge point.

As blade starts cutting the ! WARNING material, release the lower

guard immediately. When the foot rests flat on the surface being cut, proceed cutting in forward direction to end of cut.

Allow blade to come to a ! WARNING complete stop before lifting

the saw from cut. Also, never pull the saw

backward since blade will climb out of the material and KICKBACK will occur. Turn saw around and finish the cut in the normal manner, sawing forward. If corners of your pocket cut are not completely cut through, use a jigsaw or hand saw to finish the corners.

FIG. 10

LOWER

GUARD

LIFT

LEVER

FOOT

CUTTING LARGE SHEETS

Large sheets and long boards sag or bend, depending on support. If you attempt to cut without leveling and properly supporting the piece, the blade will tend to bind, causing KICK-BACK and extra load on the motor (Fig. 11).

Support the panel or board close to the cut, as shown in (Fig. 12). Be sure to set the depth of the cut so that you cut through the sheet or

board only and not the table or work bench. The two-by-fours used to raise and support the work should be positioned so that the broadest sides support the work and rest on the table or bench. Do not support the work with the narrow sides as this is an unsteady arrangement. If the sheet or board to be cut is too large for a table or work bench, use the supporting two-by-fours on the floor and secure.

FIG. 11

WRONG

FIG. 12

RIGHT

-12-

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Call Toll Free for See Voir Ver la páginaGeneral Power Tool Safety Warnings Work area safetyElectrical safety Personal safetySafety Rules for Circular Saws Battery tool use and careService Cutting proceduresKickback and related warnings Causes and operator prevention KickbackAdditional Safety Warnings Some dust created by powerLower guard function Symbols Name Designation/ExplanationSymbols Functional Description and Specifications Cordless Circular SawAssembly VARI-TORQUE ClutchLarge Diameter Faces Blade Mark Outer Wrenchwasher Outer WasherSafety Switch Release Button Cutting Angle Check Operating InstructionsTrigger Foot Blade ScrewQuadrant Bevel Adjustment Knob Line Guide Vertical Cuts Bevel SwitchBrake General CutsCutting MASONRy/METAL Plunge CutsLower Guard Lift Lever Foot Cutting Large Sheets Wrong RightRIP Cuts RIP Board GuideDesired Width CUT RIP FenceMaintenance AccessoriesCleaning Sécurité du lieu de travail Sécurité électriqueUtilisation et entretien des outils Consignes de sécurité pour scies circulaires ÉlectroportatifsUtilisation et entretien des outils à piles EntretienProblèmes associés Avertissements supplémentaires concernant la sécurité Fonction du garde inférieurSymboles Symbole Nom Désignation/ExplicationSymboles suite Description fonctionnelle et spécifications Scies circulaires sans filNuméro de modèle Bloc-piles/chargeursAssemblage Embrayage « VARI-TORQUE »Graduation Rondelle Cléexterieure Goujon DE Lame Serrer DesserrerConsignes de fonctionnement Reglage DE LA Profondeur DE CoupeVerification DE L’ANGLE DE Coupe Gâchette VIS Semelle LameReglage DE LA Coupe EN Biseau Secteur GradueGuide D’ALIGNEMENT Coupes VerticalesSciage DES Matériaux DE Maçonnerie ET DES Métaux Coupes EN GuichetMauvaise Manière Bonne Coupes DE Refente Utilisation D’UNE Planche Comme Guide DE RefenteInsertion ET Retrait DU BLOC-PILES Accessoires EntretienNettoyage Seguridad del área de trabajo Seguridad eléctricaUso y cuidado de las herramientas Mecánicas Normas de seguridad para sierras circulares Uso y cuidado de las herramientas Alimentadas por bateríasServicio de ajustes y reparaciones Procedimientos de corteEl retroceso y advertencias relacionadas El operadorAdvertencias de seguridad adicionales Función del protector inferiorSímbolos Símbolo Nombre Designación/explicaciónSímbolos continuación Descripción funcional y especificaciones Sierras circulares sin cordónEnsamblaje Embrague DE PAR Motor VariableMarca Arandela Llaveexterior Perno DE LA Hoja Apretar AflojarInstrucciones de funcionamiento Ajuste DE Inclinacion Cuadrante Pomo DE Ajuste DE Inclinacion Guía DE LíneaCortes Guia DE InterruptorCorte DE Mampostería Y Metal Cortes POR PenetraciónIncorrecto Correcto Cortes AL Hilo TABLERO-GUIA Para Cortar AL HiloAncho DE Corte Deseado PomoMantenimiento AccesoriosServicio LimpiezaBM 2610034442 03-14CCS180 3/27/14 1225 PM Remarques Notas 2610034442
Top Page Image Contents