Porter-Cable PCL120DD Screw Driving, On Board BIT Storage, Belt Clip, Drilling in Wood

Page 10

KEYLESS CHUCK - FIGURE H

H

WARNING: Make certain the lock-off

 

button is engaged to prevent switch actuation

 

before installing or removing accessories.

 

To insert a drill bit or other accessory:

 

1. Grasp the chuck (5) and rotate it in the

 

counterclockwise direction, as viewed

 

from the chuck end.

 

2. Insert the bit or other accessory fully into

 

the chuck, and tighten securely by

 

rotating the chuck in the clockwise

 

direction as viewed from the chuck end.

5

WARNING: Do not attempt to tighten

 

drill bits (or any other accessory) by gripping

 

the front part of the chuck and turning the tool on. Damage to the chuck and personal injury may occur when changing accessories.

SCREW DRIVING

For driving fasteners, the reversing button should be pushed to the left. Use reverse (button pushed to the right) for removing fasteners. When moving from forward to reverse, or vice versa, always release the trigger switch first.

ON BOARD BIT STORAGE

A magnetic bit storage slot (6) is built-in to the area on the top of the tool.

BELT CLIP

A belt clip (10) is provided which can be switched to either side of the tool.

DRILLING

• Use sharp drill bits only.

• Support and secure work properly, as instructed in the Safety Instructions.

• Use appropriate and required safety equipment, as instructedin the Safety Instructions.

• Secure and maintain work area, as instructed in the Safety Instructions.

• Run the drill very slowly, using light pressure, until the hole is started enough to keep the drill bit from slipping out of it.

• Apply pressure in a straight line with the bit. Use enough pressure to keep the bit biting

• but not so much as to stall the motor or deflect the bit.

Hold the drill firmly with one hand on the grip and the other hand on the bottom of the tool to control its twisting action.

• DO NOT CLICK THE TRIGGER OF A STALLED DRILL OFF AND ON IN AN ATTEMPT TO STARTIT. DAMAGE TO THE DRILL CAN RESULT.

• Minimize stalling on breakthrough by reducing pressure and slowly drilling through the last part of the hole.

• Keep the motor running while pulling the bit out of a drilled hole. This will help reduce jamming.

• Make sure switch turns drill on and off.

DRILLING IN WOOD

Holes in wood can be made with the same twist drill bits used for metal or with spade bits. These bits should be sharp and should be pulled out frequently when drilling to clear chips from the flutes.

DRILLING IN METAL

Use a cuttinglubricantwhen drilling metals.The exceptionsare cast iron and brass which should be drilled dry.The cutting lubricantsthat work best are sulfurized cutting oil or lard oil.

THE RBRC™ SEAL

The RBRC™ (Rechargeable Battery Recycling Corporation) Seal on the lithium-ion battery (or battery pack) indicates that the costs to recycle the battery (or battery pack) at the end of its useful life have already been paid by

PORTER-CABLE.

RBRC™ in cooperation with PORTER-CABLE and other battery users, has established programs in the United States to facilitate the collection of spent lithium-ion batteries. Help protect our environment and conserve natural resources by returning the spent

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Advertencia Léase Este Catalog Number PCL120DDGeneral Power Tool Safety Warnings Work area safetyPage Volts AmperesHertz Watts Wire Size AWG Important Safety Instructions for Battery ChargersImportant Safety Instruction for Battery Packs Read ALL InstructionsHOT/COLD Pack Delay Charger DiagnosticsBAD Battery Important Charging NotesInstalling and Removing the Battery Pack from the Tool Breaks or cracks, return to a service center for recyclingBefore removing or installing battery LED Work Light Trigger Switch & FORWARD/REVERSE Button Figure EAdjusting Torque Control Figure F Dual Range Gearing Figure GBelt Clip Screw DrivingOn Board BIT Storage DrillingMaintenance Replacement Parts Service and RepairsPage Highway 45, North Jackson, TN Perceuse/visseuse sans fil, de 12V max*, 10mm 3/8 po Manuel dinstructionsAvertissements de sécurité généraux pour les outils Page Lʼoutil Exposition au bruit peut entraîner une perte auditivePeut entraîner des blessures corporelles · le plomb dans les peintures à base de plombSymboles Description Fonctionnelle Figure aManuels fournis avec lʼoutil avant dʼutiliser le chargeur D. un dessus de table ou dʼétabli Remplacer immédiatementChargeur peut enflammer de la poussière ou des émanations Procédure DE Charge Recommandations EN Matière DE RangementFonctions DE Diagnostic DU Chargeur Pile EN Mauvais ÉtatNe jamais ouvrir le bloc-piles pour Fonction DE Suspension DU BLOC-PILES CHAUD/FROIDRemarques Importantes Pour LE Chargement Insertion ET Retrait DU BLOC-PILES DE LʼOUTILArrière Figure E Retrait DU BLOC-PILES Enfoncer le bouton deDétente ET Bouton DE Marche AVANT/MARCHE Lampe DE Travail À DELMandrin AUTO-SERRANT Figure H Mode TournevisEngrenage À Deux Vitesses Figure G Rangement Intégré DES EmboutsEntretien Mode PerçagePerçage DU Métal Pièces DE Rechange Entretien ET RéparationDépannage AccessoiresProblème Solution possible Cause possible MaximiserladuréedevieduPage ACHIEVEMENT. Ourtools Manual deinstrucciones CPCL120DDNOscuras propician accidentes Interruptor es peligrosa y debe ser reparada Quemadurasterminal al otroo incendioNormas DE Seguridad Específicas Descripción DE LAS Funciones Figura aEléctrica o electrocución Para trabajar juntosDe incendio, descarga eléctrica o electrocución Medida mínima del conductorEl líquido de la batería puede Prematura de las célulasRetraso POR Paquete CALIENTE/FRÍO Diagnóstico DEL CargadorBatería EN MAL Estado Notas Importantes Sobre LA CargaInstrucciones DE Operación Interruptor Disparador Y Botón DE AVANCE/REVERSA Figura EEngranaje DE Doble Alcance LUZ DE Trabajo DE LEDAjuste DEL Control DE Torsión Portabrocas SIN Llave Figura HSujetador Para Cinturón DestornilladoEspacio EN LA Herramientapara Guardar Puntas TaladradoDetección DE Problemas Mantenimiento Y ReparacionesPiezas DE Repuesto AccesoriosReemplazo DE LAS Etiquetas DE Advertencia Page Especificaciones del cargador

PCL120DD specifications

The Porter-Cable PCL120DD is a versatile and powerful cordless drill driver engineered for both DIY enthusiasts and professionals. This tool stands out for its combination of performance, durability, and ease of use. With a lightweight design and ergonomic grip, the PCL120DD is perfect for extended use without causing excessive hand fatigue.

One of the standout features of the PCL120DD is its compact and lightweight design, weighing just under 3.5 pounds. This makes it easy to maneuver, especially in tight spaces where other drills may struggle. The tool is equipped with a high-performance 20V MAX lithium-ion battery which provides longer runtime and less downtime during projects. This battery technology ensures that users can work longer without the need for frequent recharging.

The PCL120DD features a two-speed transmission, which allows users to switch between speeds of 0-350 RPM for low-speed applications and 0-1,500 RPM for high-speed drilling and driving tasks. This versatility makes it suitable for a variety of tasks, from assembling furniture to tackling heavier-duty jobs around the home or job site.

Another notable aspect of the PCL120DD is its 1/2-inch keyless chuck that allows for quick and easy bit changes without the need for additional tools. This feature is particularly beneficial for users who frequently swap out bits during their projects, ensuring that they can maintain productivity without interruption.

In addition to its performance capabilities, the Porter-Cable PCL120DD incorporates a built-in LED light that illuminates the work area for improved visibility in low-light conditions. This feature enhances safety and accuracy, enabling users to work efficiently without straining their eyes.

Furthermore, the PCL120DD’s robust construction ensures resilience against wear and tear, making it a reliable choice for a variety of applications. The tool is designed to withstand the rigors of professional use while remaining accessible for home projects.

Overall, the Porter-Cable PCL120DD is an impressive drill driver that combines innovative technology, user-friendly features, and solid construction. Whether you are a seasoned contractor or a novice DIYer, this tool offers the performance and functionality needed to tackle any drilling or driving tasks with confidence and efficiency.
Top Page Image Contents