Porter-Cable PCL120DD instruction manual Charger Diagnostics, BAD Battery, HOT/COLD Pack Delay

Page 7

WARNING: Never attempt to open the battery pack for any reason. If battery pack

case is cracked or damaged, do not insert into charger. Do not crush, drop or damage

battery pack. Do not use a battery pack or charger that has receiveda sharp blow, been

dropped, run over or damaged in any way (i.e., pierced with a nail, hit with a hammer,

stepped on). Damaged battery packs should be returned to service center for recycling.

WARNING: Fire hazard. Do not store or carry battery so that metal objects can

contact exposed battery terminals. For example, do not place battery in aprons,

pockets, tool boxes, product kit boxes, drawers, etc., with loose nails, screws, keys, etc.

Transporting batteriescan possibly cause fires if the battery terminals

inadvertentlycome in contact with conductive materialssuch as keys, coins,

hand tools and the like. The US Department of TransportationHazardous Material

Regulations(HMR) actually prohibit transportingbatteries in commerce or on airplanes

(i.e., packed in suitcases and carry-on luggage) UNLESS they are properly protected

from short circuits. So when transportingindividual batteries, make sure that the battery

terminals are protected and well insulated from materials that could contact them and

cause a short circuit. NOTE: Batteries should not be put in checked baggage.

STORAGE RECOMMENDATIONS

 

 

 

 

 

1. The best storage place is one that is cool and dry away from direct sunlight and

excess heat or cold.

 

 

 

 

 

2. Long storage will not harm the battery pack or charger.

 

 

 

 

 

CHARGING PROCEDURE

 

 

 

 

 

PORTER-CABLEchargers are designed to charge PORTER-CABLEbattery packs in

30-60 minutes depending on the pack being charged.

B

1. Plug the charger (11) into an appropriate outlet before

7

inserting the battery pack (7).

2. Insert the battery pack into the charger. (Fig. B)

 

 

 

 

 

 

 

 

 

 

 

 

 

3. The green LED will flash indicatingthatthe battery

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

pack is being charged.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4. The completion of charge is indicated by the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

green LED remaining on continuously. The battery

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

pack is fully charged and may be used at this time

11

 

 

 

 

 

 

 

or left on the charger.

 

 

 

 

 

Recharge discharged batteries as soon as possible after use or battery life may be greatly diminished. For longest battery life, do not discharge batteries fully. It is recommended that the batteries be recharged after each use.

CHARGER DIAGNOSTICS

This charger is designed to detect certainproblems that can arise with the batterypacks or the power source. Problems are indicated by one LED flashing in different patterns.

BAD BATTERY

The charger can detect a weak or damaged battery. The red LED flashes in the pattern indicated on the label. If you see this bad battery blink pattern, do not continue to charge the battery. Return it to a service center or a collection site for recycling.

HOT/COLD PACK DELAY

When the charger detects a battery that is excessively hot or excessively cold, it automatically starts a Hot/Cold Pack Delay, suspending charging until the battery has normalized. After this happens, the charger automatically switches to the Pack Charging mode. This feature ensures maximum battery life. The red LED flashes in the pattern indicated on the label.

IMPORTANT CHARGING NOTES

1. Longest life and best performance can be obtained if the battery pack is charged when the air temperature is between 65°F and 75°F (18°- 24°C). DO NOT charge the battery pack in an air temperature below +40°F (+4.5°C), or above +105°F (+40.5°C). This is important and will prevent serious damage to the battery pack.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Catalog Number PCL120DD Advertencia Léase EsteWork area safety General Power Tool Safety WarningsPage Volts AmperesHertz Watts Important Safety Instructions for Battery Chargers Wire Size AWGRead ALL Instructions Important Safety Instruction for Battery PacksImportant Charging Notes Charger DiagnosticsBAD Battery HOT/COLD Pack DelayInstalling and Removing the Battery Pack from the Tool Breaks or cracks, return to a service center for recyclingBefore removing or installing battery Dual Range Gearing Figure G Trigger Switch & FORWARD/REVERSE Button Figure EAdjusting Torque Control Figure F LED Work LightDrilling Screw DrivingOn Board BIT Storage Belt ClipReplacement Parts Service and Repairs MaintenancePage Highway 45, North Jackson, TN Manuel dinstructions Perceuse/visseuse sans fil, de 12V max*, 10mm 3/8 poAvertissements de sécurité généraux pour les outils Page · le plomb dans les peintures à base de plomb Exposition au bruit peut entraîner une perte auditivePeut entraîner des blessures corporelles LʼoutilSymboles Figure a Description FonctionnelleManuels fournis avec lʼoutil avant dʼutiliser le chargeur D. un dessus de table ou dʼétabli Remplacer immédiatementChargeur peut enflammer de la poussière ou des émanations Pile EN Mauvais État Recommandations EN Matière DE RangementFonctions DE Diagnostic DU Chargeur Procédure DE ChargeInsertion ET Retrait DU BLOC-PILES DE LʼOUTIL Fonction DE Suspension DU BLOC-PILES CHAUD/FROIDRemarques Importantes Pour LE Chargement Ne jamais ouvrir le bloc-piles pourLampe DE Travail À DEL Retrait DU BLOC-PILES Enfoncer le bouton deDétente ET Bouton DE Marche AVANT/MARCHE Arrière Figure ERangement Intégré DES Embouts Mode TournevisEngrenage À Deux Vitesses Figure G Mandrin AUTO-SERRANT Figure HPièces DE Rechange Entretien ET Réparation Mode PerçagePerçage DU Métal EntretienMaximiserladuréedeviedu AccessoiresProblème Solution possible Cause possible DépannagePage ACHIEVEMENT. Ourtools CPCL120DDN Manual deinstruccionesOscuras propician accidentes Quemadurasterminal al otroo incendio Interruptor es peligrosa y debe ser reparadaNormas DE Seguridad Específicas Funciones Figura a Descripción DE LASMedida mínima del conductor Para trabajar juntosDe incendio, descarga eléctrica o electrocución Eléctrica o electrocuciónPrematura de las células El líquido de la batería puedeNotas Importantes Sobre LA Carga Diagnóstico DEL CargadorBatería EN MAL Estado Retraso POR Paquete CALIENTE/FRÍOInterruptor Disparador Y Botón DE AVANCE/REVERSA Figura E Instrucciones DE OperaciónPortabrocas SIN Llave Figura H LUZ DE Trabajo DE LEDAjuste DEL Control DE Torsión Engranaje DE Doble AlcanceTaladrado DestornilladoEspacio EN LA Herramientapara Guardar Puntas Sujetador Para CinturónMantenimiento Y Reparaciones Detección DE ProblemasAccesorios Piezas DE RepuestoReemplazo DE LAS Etiquetas DE Advertencia Page Especificaciones del cargador

PCL120DD specifications

The Porter-Cable PCL120DD is a versatile and powerful cordless drill driver engineered for both DIY enthusiasts and professionals. This tool stands out for its combination of performance, durability, and ease of use. With a lightweight design and ergonomic grip, the PCL120DD is perfect for extended use without causing excessive hand fatigue.

One of the standout features of the PCL120DD is its compact and lightweight design, weighing just under 3.5 pounds. This makes it easy to maneuver, especially in tight spaces where other drills may struggle. The tool is equipped with a high-performance 20V MAX lithium-ion battery which provides longer runtime and less downtime during projects. This battery technology ensures that users can work longer without the need for frequent recharging.

The PCL120DD features a two-speed transmission, which allows users to switch between speeds of 0-350 RPM for low-speed applications and 0-1,500 RPM for high-speed drilling and driving tasks. This versatility makes it suitable for a variety of tasks, from assembling furniture to tackling heavier-duty jobs around the home or job site.

Another notable aspect of the PCL120DD is its 1/2-inch keyless chuck that allows for quick and easy bit changes without the need for additional tools. This feature is particularly beneficial for users who frequently swap out bits during their projects, ensuring that they can maintain productivity without interruption.

In addition to its performance capabilities, the Porter-Cable PCL120DD incorporates a built-in LED light that illuminates the work area for improved visibility in low-light conditions. This feature enhances safety and accuracy, enabling users to work efficiently without straining their eyes.

Furthermore, the PCL120DD’s robust construction ensures resilience against wear and tear, making it a reliable choice for a variety of applications. The tool is designed to withstand the rigors of professional use while remaining accessible for home projects.

Overall, the Porter-Cable PCL120DD is an impressive drill driver that combines innovative technology, user-friendly features, and solid construction. Whether you are a seasoned contractor or a novice DIYer, this tool offers the performance and functionality needed to tackle any drilling or driving tasks with confidence and efficiency.
Top Page Image Contents