Porter-Cable 90550130 Keyless Chuck Figure, Screw Driving, On Board Bit Storage, Drilling

Page 11

90550130 PC1800HD hammer drill 4/3/09 2:40 PM Page 11

Keyless Chuck - Figure I

To insert a drill bit or other accessory:

1.Grasp the chuck (5) and rotate it in the counterclockwise direction, as viewed from the chuck end.

2.Insert the bit or other accessory fully into the chuck, and tighten securely by rotating the chuck in the clockwise direction as viewed from the chuck end.

: Do not attempt to tighten drill bits (or any other accessory) by gripping the front part of the chuck and turning the tool on. Damage to the chuck and personal injury may occur when changing accessories.

I

14

12

5

10

8

Screw Driving

For driving fasteners, the reversing button should be pushed to the left. Use reverse (button pushed to the right) for removing fasteners. When moving from forward to reverse, or vice versa, always release the trigger switch first.

On Board Bit Storage

A bit storage slot is built-in to the area just above the battery.

Drilling

Use sharp drill bits only.

Support and secure work properly, as instructed in the Safety Instructions.

Use appropriate and required safety equipment, as instructed in the Safety Instructions.

Secure and maintain work area, as instructed in the Safety Instructions.

Run the drill very slowly, using light pressure, until the hole is started enough to keep the drill bit from slipping out of it.

Apply pressure in a straight line with the bit. Use enough pressure to keep the bit biting but not so much as to stall the motor or deflect the bit.

Hold the drill firmly with one hand on the grip and the other hand on the bottom of the battery pack to control its twisting action.

DO NOT CLICK THE TRIGGER OF A STALLED DRILL OFF AND ON IN AN ATTEMPT TO START IT. DAMAGE TO THE DRILL CAN RESULT.

Minimize stalling on breakthrough by reducing pressure and slowly drilling through the last part of the hole.

Keep the motor running while pulling the bit out of a drilled hole. This will help reduce jamming.

Make sure switch turns drill on and off.

Drilling in Wood

Holes in wood can be made with the same twist drill bits used for metal or with spade bits. These bits should be sharp and should be pulled out frequently when drilling to clear chips from the flutes.

Drilling in Metal

Use a cutting lubricant when drilling metals. The exceptions are cast iron and brass which should be drilled dry. The cutting lubricants that work best are sulfurized cutting oil or lard oil.

Drilling in Masonry

Use carbide tipped masonry bits. Refer to Drilling section. Keep even force on the drill but not so much that you crack the brittle material. A smooth, even flow of dust indicates the proper drilling rate.

11

Image 11
Contents PC1800HD Advertencia Léase EsteCatalog Number Work area safety General Power Tool Safety WarningsSpecific Safety Rules Symbols Safety Guidelines DefinitionsNI-CD Battery Packs and Chargers Description Cat. # Important Safety Instructions for Battery ChargersWire Size AWG LI-ION Battery Packs and Chargers Description Cat. #Read ALL Instructions Important Safety Instruction for Battery PacksStorage Recommendations Battery CAP InformationCharging Procedure Leaving the battery in the charger Bad batteryHot/Cold pack delay Problem power lineSafety Warnings and Instructions Drills Installing and Removing the Battery Pack From the ToolDual Range Gearing Figure H Trigger Switch & Forward/Reverse Button Figure FAdjusting Torque Control Figure G Hammer ActionDrilling Keyless Chuck FigureScrew Driving On Board Bit StorageSpecialnotes for USE with Lithium Batteries TroubleshootingMaintenance Replacement Parts Service and RepairsAccessories Three Year Limited WarrantyDE Catalogue Manuel dinstructions90550130 PC1800HD hammer drill 4/3/09 240 PM 90550130 PC1800HD hammer drill 4/3/09 240 PM Consignes DE Sécurité Particulières Description De cat SymbolesLignes Directrices EN Matière DE Sécurité Définitions Calibre AWGDescription fonctionnelle Lire Toutes LES Directives Procédure DE Charge Recommandations EN Matière DE RangementInformation Concernant LE Capuchon DU BLOC-PILE Laisser de piles au LI-ION dans les bagages enregistrésProblème Avec LE Secteur Fonctions DE Diagnostic DU ChargeurPile EN Mauvais État Fonction DE Suspension DU BLOC-PILES CHAUD/FROIDLa figure E Avertissements de sécurité et directives perceusesInsertion ET Retrait DU BLOC-PILES DE L’OUTIL Réglage DU Couple Figure G FonctionnementPercussion Rangement Intégré DES Embouts Mode TournevisMode Perçage Mandrin AUTO-SERRANT FigureEntretien LE Sceau SrprcmcDépannage Remarques Spéciales SUR L’EMPLOIAVEC DES Pilesau LithiumEntretien ET Réparation AccessoiresRemplacement DES Étiquettes D’AVERTISSEMENT Garantie Limitée DE Trois ANSHighway 45 North Jackson, Tennessee 888 Catálogo N Taladro percutor inalámbrico de 13 mm 1/2 pulgadas y 18Manual deinstrucciones 90550130 PC1800HD hammer drill 4/3/09 240 PM 90550130 PC1800HD hammer drill 4/3/09 240 PM Normas DE Seguridad Específicas Descripción De cat Pautas DE SEGURIDAD/DEFINICIONESSímbolos Tamaño AWG del conductorFigura a Descripción DE LAS FuncionesLEA Todas LAS Instrucciones Procedimiento DE Carga Información Acerca DEL Protector DE LA BateríaRecomendaciones CON Respecto AL Almacenamiento Retraso POR Paquete CALIENTE/FRÍO Línea DE Potencia CON ProblemasDiagnóstico DEL Cargador Batería EN MAL EstadoInstrucciones Y Advertencias DE Seguridad Taladros En la figura CAjuste DEL Control DE Torsión Figura G Instrucciones DE OperaciónAcción de percusión Interruptor Disparador Y Botón DE AVANCE/REVERSA Figura FTaladrado Portabrocas SIN Llave FiguraDestornillado Espacio EN LA Herramienta Para Guardar PuntasEL Sello Rbrc Detección DE ProblemasTaladrado EN Mampostería Notas Especiales Paraeluso CON Baterías DE LitioAccesorios Garantía Limitada DE Tres AñosPiezas DE Repuesto Mantenimiento Y Reparaciones Reemplazo DE LAS Etiquetas DE Advertencia Catalog Numbers PC1800HD Form # April Especificaciones