Infortrend 170 manual This device is in conformity with the EMC

Page 4

Warnings and Certifications

FCC (applies in the U.S. and Canada)

This device complies with Part 15 of FCC Rules. Operation of this device is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation.

Warning:

Use only shielded cables to connect I/O devices to this equipment.

You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.

This device is in conformity with the EMC

Image 4
Contents Installation and Hardware Reference Manual 320MB/sec SCSI-to-SCSI RAID ControllerContact Information Asia Pacific International HeadquartersChina AmericasCopyright This Edition First PublishedDisclaimer TrademarksThis device is in conformity with the EMC Table of Contents Controller Monitoring Appendix C Hardware Troubleshooting Safety Precautions Precautions and InstructionsESD Precautions About This ManualWho should read this manual? ConventionsRelated Documentation NamingSoftware and Firmware Updates Product Overview Chapter IntroductionProduct Introduction Enclosure Controller BoxFront Side Rear SideLCD Panel SR ComponentsController Board Connector Type Label Description JP1 and JP13Interfaces Controller Board FrontConnector Type Label Description SR Accessory Items Separately Purchased Accessory ItemsPower Connector 4 I2C Signal Compatible CablesBattery Backup Unit BBU Optional ItemsEnvironmental Requirements Power Supply RequirementsDaughter Board Expansion LED Indicators SR Controller MonitoringCooling Requirements 1 I2C BusAudible Alarms This page is intentionally left blank Chapter Installation Installation OverviewInstallation Prerequisites General ConsiderationsHardware Installation Preparation Static-free InstallationTools or Equipment Needed for Installing the Subsystem Planning Before InstallationGeneral Installation Procedure Unpacking the ControllerOverview Accessing the Controller BoardRemoving and Replacing the Chassis Top Cover Dimm Module Installation Procedure Memory Module InstallationSelecting the DIMMs Battery Backup Unit BBU Installation About the First BBU InstallationBBU Installation Procedure Remove the Battery Connector CapInstall the Battery Charger Board About Daughter Board Installation Daughter Board InstallationDaughter Board Installation Procedure Daughter Board Installation Chapter Controller Monitoring Controller Monitoring OverviewStatus-indicating LEDs PWRDefault Threshold Values Audible AlarmI2C Port Enclosure Monitoring I2C Port Enclosure Monitoring 1 I/O Channel Configuration Chapter Controller Connections OperationSentinelRAID Connection Host ConnectionSR 170 Topologies Drive ConnectionScsi Termination Unique IDsSR 170 Topologies Dual Host Connection Dual Host ConnectionController Integration ExpansionConnecting RS-232C Terminal Emulation Power ConnectionOther Connections Power On Check ListPower On Sequence LCD ScreenPower Off Procedure Stop I/O access to the system Disconnect the hostPower Off Procedure Chapter Controller Maintenance Controller Maintenance OverviewAbout Controller Maintenance User Serviceable ComponentsDimm Module Replacement Procedure When should a Dimm module be replaced?Replacing a failed Dimm Module Replacing a failed Dimm Module About BBU Maintenance Replacing a Failed Optional BBU ModuleOnce the controller board has pack from the charger board Daughter Board Maintenance BBU Charger Board ReplacementAbout Daughter Board Maintenance Replacing a Daughter BoardRemove the Daughter Board Retention Screws This page is intentionally left blank Appendix a SentinelRAID Features Flexible ConfigurationUser-friendly Configuration Utilities SCSI-320 I/O ChannelsOther Fault Tolerant Features Controller ArchitectureGlobal and Local Spares Hot-swapping of DrivesRAID Levels Supported Controller ChassisThis page is intentionally left blank Configuration Appendix B Hardware SpecificationsSpecification Feature Controller Architecture RAID ManagementFault Tolerance Technical Specifications Specification SizeDescription Specification SoftwareController Specifications Technical Specifications Appendix C Hardware Troubleshooting ProblemProblem Installed. Reinstall a Dimm module will usually solve This page is intentionally left blank Appendix D Spare Parts and Accessories AccessoriesAccessory Part Number Description Spare PartsAccessories Appendix E Connectors and Jumper Identification Controller Main Board InterfacesLabel Connector Name Controller Main Board Interface DescriptionsCOM Port Pin Outs LED Jumper Pin OutsPin Description J3 I2C Port Symbol Type DescriptionPin Pin Name J1 Battery Connector Symbol Parameter Rating UnitTTL Device Parameters PinIFT- 9011 Null Modem IFT-9012 RS-232C Extension CableIndex SentinelRAID 170 Installation and Hardware Reference Manual Index This page is intentionally left blank