HP Server tc2110 Installing an Optional CD-ROM or DVD Drive, Installing a Disk Drive Tray Mounted

Page 32

Chapter 3Installing and Configuring

NOTE

If the hard disk drive (HDD) you are planning to install already has a mounting tray

 

attached, you must remove it from the tray.

 

 

6.Install the hard disk drive as described below:

a.Place the hard disk drive into the tray and use the screws provided to secure it to the tray from the bottom.

b.Insert the hard disk drive assembly into the fourth shelf. See Figure 3-9.

The tabs should snap into place when the drive is pushed all the way into the fourth shelf.

Figure 3-9. Installing a Disk Drive (Tray Mounted)

7.Connect the data cable to the hard drive, as described below:

o If mounting a third IDE hard drive, connect the secondary (IDE-2) cable to the hard drive.

o If mounting a third SCSI hard drive, connect the SCSI cable to the drive and ensure all SCSI drives are connected to the SCSI cable.

There are five connectors on the standard SCSI cable; with four of the connectors intended for the three hard disk drives and one optional backup tape drive. The standard SCSI cable has a terminator at the end of the cable.

8.Connect the power cable to the rear of the hard disk drive.

9.Replace the upper bezel and left side cover.

10.Replace the external cables, and power cord, and then restore power to the Server.

The BIOS and SCSISelect utilities automatically detect the new hard drives (IDE or SCSI), but you should check the BIOS and SCSISelect settings and make changes as necessary.

Installing an Optional CD-ROM or DVD Drive

You may install an optional IDE CD-ROM or DVD drive in the third drive tray. The secondary IDE cable, which is connected to the IDE CD-ROM in the second drive tray, has an available connector that may be used for an IDE device in either the third or fourth tray.

26

Image 32
Contents HP Server tc2110 Operations and Maintenance Guide Audience Assumptions Contents Error! Bookmark not defined ContentsServer stops working hangs 105 109Controls and Indicators Front PanelAdditional Controls and Indicators Sleep LEDRear Panel Applying Power to the HP Server Connecting the Power CordsConnecting the Power Cords Powering-Up the ServerSetting the input voltage Sleep States Acpi Powering-Down the ServerConnecting Power to Multiple-Server Configurations Chapter Page Serial Port Connector External ConnectorsMini-DIN PS/2 Connectors Parallel Port Connector USB ConnectorPin LVD Scsi Port Connector Low Voltage Differential Pin 1 LVD Scsi Connector MalePin Narrow Scsi Port Connector Accessory Board PositionStandard LAN Connector Page Removing the Left Side Cover Installing and ConfiguringOpening and Closing the HP Server Replacing the Left Side Cover Removing the Left Side CoverRemoving the Upper Bezel Replacing the Left Side CoverReplacing the Upper Bezel Removing the Upper Front BezelMass Storage Replacing the Upper BezelMass Storage Guidelines Mass Storage LocationsIDE Mass Storage Devices Boot PriorityIDE Controller Configuration IDE Mass Storage Additions Scsi Controller ConfigurationScsi Mass Storage Devices Installing a Second Hard Disk Drive Drive Cage Mounted Scsi Mass Storage AdditionsReleasing the Retaining Clips Installing a Third Hard Disk Drive Tray Mounted Drive Cage MountingInstalling an Optional CD-ROM or DVD Drive Installing a Disk Drive Tray Mounted10. Installing an Optional CD-ROM or DVD Drive Installing an Optional Backup Tape Drive Tools Required Memory Installation GuidelinesMemory Modules Installing Additional DIMMs 12. Dimm Locations on System Board Processor Removing DIMMsRemoving the Heat Sink and Cooling Fan 15. Removing Heat Sink and Cooling FanRemoving the Processor Replacing the ProcessorReplacing the Heat Sink and Cooling Fan 17. Replacing the ProcessorAccessory Boards Tested PCI BoardsIRQ Settings GuidelinesInstalling an Accessory Board Particular accessory board type 21. Removing the Slot Cover Connecting Peripheral Devices Removing Accessory BoardsUninterruptible Power Supply UPS Monitor, Keyboard, and MouseHP Startup CD-ROM Configuring the HP Server tc2110Accessing the HP Startup CD-ROM Bios Setup Utility Contents of the HP Startup CD-ROMNOS Installation DiagtoolsMenu Bar Accessing the Setup UtilityViewing the Summary Configuration Screen Using the Setup Screens Changing the System Date and TimeSetting Boot Passwords Scsi Configuration Utility Diagnostics Power-On Self Test PostNo Error Messages Displayed Post Error MessagesAfter Installing an Accessory General ChecksClearing the Cmos and Passwords Location of Configuration Switches HP Server Diagtools HP Diagtools CapabilitiesAbout Error Messages Advantages and Limitations of Hardware DiagnosticsHP Toptools Some limitations areBeep Codes Error MessagesPower-On Self Test Post Error Messages Troubleshooting Tools Maintenance and TroubleshootingPreventive Maintenance Procedures Troubleshooting Other Support InformationTroubleshooting Checklist Bios Update/Recovery Bios Reset/Update/RecoveryBios Reset Password Problems Clearing the Bios ConfigurationSupervisor Password User PasswordConfiguration and Password Switch Location Operating System Not Found Message AppearsPower Problems Server Stops or Hangs While Starting UpVideo/Monitor Problems Configuration Problems Printer ProblemsKeyboard Does Not Work Mouse Does Not WorkEnvironmental problems result from Flexible Disk and Flexible Disk Drive ProblemsFlexible Disk Drive Problems CD-ROM Drive is Not Working Properly CD-ROM ProblemsCD-ROM Drawer Will Not Open Scsi Controller Does Not Work At Initial Installation Scsi ProblemsServer Will Not Boot From a CD-ROM Disk Scsi Device Does Not Work After Installation Scsi Device Stops WorkingProcessor Problems Memory ProblemsNetwork Interface Card embedded or PCI Problems LEDs are not lit on the NIC Service Tools Required Replacing PartsSafety Information Mass Storage Devices Removing the Flexible Disk DriveReplacing the Flexible Disk Drive Removing the CD-ROMReplacing the CD-ROM Removing the CD-ROMRemoving a Backup Tape Drive Replacing a Backup Tape DriveRemoving a Hard Disk Drive Tray Mounted Replacing a Hard Disk Drive Tray Mounted Removing Hard Disk Drive HDD and TrayRemoving a Hard Disk Drive Drive Cage Mounted DIMMs Replacing a Hard Disk Drive Drive Cage MountedReplacing DIMMs Removing DIMMs from System BoardDimm to Slot Alignment 10. Removing Heat Sink and Cooling Fan 11. Removing the Processor 12. Replacing the Processor 13. Replacing Heat Sink-Cooling Fan on the Processor Replacing Accessory Boards 14. Removing Slot Cover LatchSlot Cover Power Supply Removing the Power SupplyRemoving the Battery BatteryReplacing the Power Supply Removing the Chassis Fan Replacing the BatteryChassis Fan Replacing the Chassis Fan 19. Removing the Chassis FanSystem Board Removing the System BoardReplacing the System Board 20. Removing and Replacing the System BoardPage Parts Identification Exploded View Covers and BezelsExploded View Mass Storage Devices Exploded View Chassis Fan, Power Supply, and System Board Exploded View System Board Components Replaceable Parts List Cables and Part Numbers Power Cords KeyboardsPage Specifications Weight and DimensionsPower Supply Specifications EnvironmentalHardware Specifications IDESystem Board Components/Connectors 107 System Board LayoutPage Index AcpiKeyboards Part numbers Scsi ID ZIF
Related manuals
Manual 1 pages 3.34 Kb Manual 4 pages 49.92 Kb Manual 65 pages 57.66 Kb

Server tc2110 specifications

The HP Server tc2110 is a robust and versatile solution designed to meet the needs of small to medium-sized businesses looking for reliability and performance in their IT infrastructure. This server is built on the foundation of HP's renowned engineering, making it a trusted choice for organizations needing dependable server capabilities.

One of the standout features of the HP tc2110 is its scalability. With support for multiple processors, organizations can easily upgrade their server capabilities as their needs grow. This makes it an ideal choice for businesses that anticipate future expansion and require a server that can grow alongside them. The tc2110 supports various Intel Xeon processors, offering excellent processing power and efficiency.

Another significant characteristic of the tc2110 is its high capacity for memory. The server can support substantial RAM, which enhances its multitasking capabilities and allows it to handle demanding applications with ease. This memory capacity is complemented by the server's support for various storage options, including traditional hard drives and modern solid-state drives, enabling businesses to optimize performance and data access speeds according to their specific needs.

The HP Server tc2110 also emphasizes security features, which are critical for today’s evolving cybersecurity landscape. It includes advanced hardware security features such as Trusted Platform Module (TPM) and secure boot, ensuring that data is protected against unauthorized access and potential threats.

In addition to its impressive hardware capabilities, the tc2110 is designed with energy efficiency in mind. Its intelligent cooling technologies and power management features help reduce overall operational costs while maintaining optimal performance. This makes the server not only a powerful option but also a more environmentally friendly choice, aligning with the growing trend towards sustainable IT practices.

Connectivity is another key aspect of the HP tc2110. It offers multiple ports for network connections, ensuring seamless integration into existing IT infrastructures. This connectivity enhances communication between devices and provides businesses with the flexibility to adapt to new technology advancements with ease.

Overall, the HP Server tc2110 is a well-rounded server solution that combines performance, scalability, security, and energy efficiency. Whether for intensive applications, data management, or general computing tasks, the tc2110 stands out as a reliable choice for enterprises seeking to establish or enhance their IT environments. Its blend of features makes it a compelling option for organizations aiming to streamline operations while minimizing costs.