HP R5500 manual Power management software

Page 31

Power management

Power management software

HP Power Manager software ensures maximum power reliability of computer systems through comprehensive control of UPSs. The easy-to-use browser interface enables novice users to configure and manage power protection settings. To download the latest version of HP Power Manager software, see the HP website (http://www.hp.com/go/rackandpower).

NOTE: To install and configure the software, see the software user guide. The software user guide is available for download from the HP website (http://www.hp.com/go/rackandpower).

HP Power Manager:

•Does not require complex management systems, which simplifies deployment, configuration, and management of UPS-protected environments.

•Manages a graceful shutdown of attached devices during utility power failures.

•Prioritizes the timing of attached load device shutdowns.

•Shuts down and reboots any UPS and attached load devices based on a user-specified schedule.

•Customizes alert generation with modifiable dialog boxes, command execution, and email and broadcast messages.

•Monitors the status of the UPS and reports alarms.

•Displays a power log for analysis.

•Manages independent UPS load segments to provide separate power control of attached load devices.

•Delays reboot by load segment after a power outage to sequence the startup of system components.

Power management 31

Image 31

Contents Part Number 351643-004A September 2007 Fourth Edition HP UPS R5500 User GuideAudience assumptions Contents Power management software Verifying the Repo port connection Powering down the UPSOrdering spares Before you contact HP HP contact information UPS spare parts list Hardware optionsDescription Component identificationUPS R5500 overview UPS front panelUPS front panel controls Powers up the UPS Starting power toFront panel is shown with the bezel removed LED description UPS front panel LED indicatorsRepo port UPS rear panelERM rear panel Tools and materials InstallationPrecautions Preparing to install the hardwareSelecting a site Installing the mounting railsReadying the equipment Installation Installation Preparing the rails for integrated shipping Installing the UPSTighten the hex nuts Installation Removing the UPS battery bracket Installing the batteries Installation Installation Connecting the Repo port Connecting the ground bonding cable Connecting devices to the UPS Connecting the UPS to utility powerGround bonding cable is not included Installation Starting power to the load Installing the ERMInstallation Installation Modes of operation Standby modeOperate mode UPS operationsExplanation when LED is illuminated Configuring the UPSConfigure mode Auto-Bypass modeAvailable settings Parameter Testing the LEDsPowering down the UPS Silencing an audible alarmVerifying the Repo port connection Power management software Power managementRemoving the UPS front bezel Removing the ERM front bezel MaintenanceReplacing the UPS electronics module Replacing the UPS option card Replacing the batteries Important battery safety informationBattery care and storage guidelines To replace the component, reverse the removal procedureUPS battery replacement procedure Replacing the ERM Replacing the UPSUpdating the UPS firmware 30? TroubleshootingLED and audible alarm troubleshooting Alarm Be silencedInput voltage is not within ±12 percent of nominal voltage Battery conditionGeneral alarm condition Bypass is out of rangeInsufficient warning of low batteries Internal UPS fault conditionLow battery shutdowns Input voltage is out of rangeRepo condition Site wiring conditionUPS does not provide the expected backup time Overload conditionUtility power condition UPS frequently switches between utility and battery powerUPS is in Auto-Bypass mode UPS is on batteryUPS input specifications SpecificationsUPS physical specifications ERM physical specificationsConfiguration setting VAC Available nominal output voltage Power protection specificationsVoltage specifications UPS model Nominal power Rating W Voltage settingOutput tolerance specifications Battery specificationsBattery runtime for NA/JPN model Battery runtime for Intl modelRepo port specifications Environmental specificationsDescription Spare part Number UPS spare parts listSpares Ordering sparesHardware options Before you contact HP Technical supportHP contact information Pre-Failure Battery Warranty Warranty informationLimited warranty $250,000 Computer Load Protection GuaranteeRegulatory compliance identification numbers Regulatory compliance noticesFederal Communications Commission notice Cables ModificationsEuropean Union regulatory notice Canadian notice Avis CanadienJapanese notice Bsmi notice Battery replacement notice Power cord statement for Japan Taiwan battery recycling noticePreventing electrostatic discharge Electrostatic dischargeGrounding methods to prevent electrostatic discharge Acronyms and abbreviations Index Communications port, connectingInstallation instructions Repo port, connecting

Related manuals

Manual 61 pages 9.34 Kb