HP R5500 manual Installation instructions

Page 60

G

general alarm condition 40 General Alarm LED, location 8 General Alarm LED, troubleshooting 39 ground bonding cable, connecting 21 grounding methods 57

H

hardware options 49

hardware, preparing to install 11 high-current output receptacle, connecting 22 high-current output receptacle, location 9 high-current output receptacle, specifications 44 HP Power Manager 31

HP technical support 50

I

identification number		52
input specifications	44
input voltage is out of range			41
installation instructions		11
installing the batteries		17
installing the ERM	24
installing the rails	12
installing the UPS	15
insufficient low battery warning 41
internal UPS fault condition			41

J

Japanese notice 55

L

LEDs, testing 29
LEDs, troubleshooting	39
LEDs, unit identification (UID)			8
limited warranty 51
load protection guarantee		51
load segments, controlling		31
load segments, location 9
load segments, specifications			44
low battery shutdowns	41

low battery warning, insufficient 41

M

maintenance 32 modes of operation 27 modifications, FCC notice 53

mounting rails 12

N

nominal voltage, configuring 28

O

On Battery LED, location 8

On Battery LED, troubleshooting 39 On button, location 7

Operate mode 27 operations, UPS 27 option card, replacing 34 optional items 49 ordering spares 48

output feature specifications 46 output specifications 44

output tolerance specifications 46 overload condition 42 Overload LED, location 8 Overload LED, troubleshooting 39 overview, HP Power Manager 31 overview, power management software 31 overview, REPO port 9

overview, UPS 6

P

phone numbers 50 physical specifications 44 power cord 56

power management 31

power protection specifications 45 powering down 30

powering up 24 preparation procedures 11 problem diagnosis 39

R

rails, installing	12
rear panel connectors			9, 10
receptacles, illustrated			9
regulatory compliance identification numbers 52
regulatory compliance notices 52, 54, 56
replacing the batteries			35, 36
replacing the electronics module 33
replacing the ERM		37
replacing the option card 34
replacing the UPS		37
REPO condition	42

Index 60

Image 60

Contents HP UPS R5500 User Guide Part Number 351643-004A September 2007 Fourth EditionAudience assumptions Contents Verifying the Repo port connection Powering down the UPS Power management softwareOrdering spares UPS spare parts list Hardware options Before you contact HP HP contact informationComponent identification UPS R5500 overviewUPS front panel DescriptionPowers up the UPS Starting power to UPS front panel controlsUPS front panel LED indicators Front panel is shown with the bezel removed LED descriptionUPS rear panel Repo portERM rear panel Installation PrecautionsPreparing to install the hardware Tools and materialsInstalling the mounting rails Selecting a siteReadying the equipment Installation Installation Installing the UPS Preparing the rails for integrated shippingTighten the hex nuts Installation Removing the UPS battery bracket Installing the batteries Installation Installation Connecting the Repo port Connecting the ground bonding cable Connecting the UPS to utility power Connecting devices to the UPSGround bonding cable is not included Installation Installing the ERM Starting power to the loadInstallation Installation Standby mode Operate modeUPS operations Modes of operationConfiguring the UPS Configure modeAuto-Bypass mode Explanation when LED is illuminatedTesting the LEDs Available settings ParameterSilencing an audible alarm Powering down the UPSVerifying the Repo port connection Power management Power management softwareMaintenance Removing the UPS front bezel Removing the ERM front bezelReplacing the UPS electronics module Replacing the UPS option card Important battery safety information Battery care and storage guidelinesTo replace the component, reverse the removal procedure Replacing the batteriesUPS battery replacement procedure Replacing the UPS Replacing the ERMUpdating the UPS firmware Troubleshooting LED and audible alarm troubleshootingAlarm Be silenced 30?Battery condition General alarm conditionBypass is out of range Input voltage is not within ±12 percent of nominal voltageInternal UPS fault condition Low battery shutdownsInput voltage is out of range Insufficient warning of low batteriesSite wiring condition UPS does not provide the expected backup timeOverload condition Repo conditionUPS frequently switches between utility and battery power UPS is in Auto-Bypass modeUPS is on battery Utility power conditionSpecifications UPS physical specificationsERM physical specifications UPS input specificationsPower protection specifications Voltage specificationsUPS model Nominal power Rating W Voltage setting Configuration setting VAC Available nominal output voltageBattery specifications Battery runtime for NA/JPN modelBattery runtime for Intl model Output tolerance specificationsEnvironmental specifications Repo port specificationsUPS spare parts list SparesOrdering spares Description Spare part NumberHardware options Technical support Before you contact HPHP contact information Warranty information Limited warranty$250,000 Computer Load Protection Guarantee Pre-Failure Battery WarrantyRegulatory compliance notices Regulatory compliance identification numbersFederal Communications Commission notice Modifications CablesCanadian notice Avis Canadien European Union regulatory noticeJapanese notice Bsmi notice Battery replacement notice Taiwan battery recycling notice Power cord statement for JapanElectrostatic discharge Preventing electrostatic dischargeGrounding methods to prevent electrostatic discharge Acronyms and abbreviations Communications port, connecting IndexInstallation instructions Repo port, connecting

Related manuals

Manual 61 pages 9.34 Kb