HP R5500 manual Index, Communications port, connecting

Page 59

Index

A

alarm cannot be silenced 39 alarm conditions 39 alarms, silencing 30 alarms, troubleshooting 39 authorized reseller 50 Auto-Bypass mode 28, 43

B

backup time, insufficient 42 batteries, care and storage 35 batteries, charging 23, 26

batteries, insufficient warning when low 41 batteries, replacing 35, 36

batteries, runtime	46
batteries, specifications		46
battery bracket 17, 18
battery circuit breaker		19
battery condition	40
Battery Fault LED, location			8
Battery Fault LED, troubleshooting 39
battery replacement notice			55
battery warranty	51
bezel, attaching	18, 25
bezel, removing	32
bracket, battery	17, 18
BSMI notice 55
buttons 6, 7
bypass is out of range		40

C

cables 53
Canadian notice	54
charging batteries	23, 26
circuit breakers, location		9, 10
circuit breakers, specifications			44
circuit breakers, switching off			25, 37
circuit breakers, switching on			22, 26
class A equipment	52
class B equipment	52
communications port, connecting 19
component identification		6, 7, 8, 9, 10

configuration of system 28 Configure button, location 7 Configure mode 28

Configure Mode On LED, location 8

connecting devices to UPS	22
connectors 6, 9, 10
contacting HP 50
cord retention clip locations	9

cord retention clips, connecting 23

D

Declaration of Conformity 53 devices, connecting 22 diagnostics 29 dimensions, ERM 44 dimensions, UPS 44 disposal, battery 55

E

electrical requirements 12
electronics module, replacing		33
electrostatic discharge 57
environmental specifications 47
ERM circuit breaker, turning off		25
ERM circuit breaker, turning on		26
ERM, configuring 28
ERM, connecting	26
ERM, identifying components		10
ERM, installing	24
ERM, replacing	37
European Union notice 54

F

FCC rating label 52

Federal Communications Commission (FCC) notice 52, 53

firmware, updating 38

frequent switching between battery and utility power 43

front panel buttons 7

front panel components 6, 7 front panel LEDs 8

Index 59

Image 59

Contents Part Number 351643-004A September 2007 Fourth Edition HP UPS R5500 User GuideAudience assumptions Contents Ordering spares Verifying the Repo port connection Powering down the UPSPower management software Before you contact HP HP contact information UPS spare parts list Hardware optionsDescription Component identificationUPS R5500 overview UPS front panelUPS front panel controls Powers up the UPS Starting power toFront panel is shown with the bezel removed LED description UPS front panel LED indicatorsRepo port UPS rear panelERM rear panel Tools and materials InstallationPrecautions Preparing to install the hardwareReadying the equipment Installing the mounting railsSelecting a site Installation Installation Tighten the hex nuts Installing the UPSPreparing the rails for integrated shipping Installation Removing the UPS battery bracket Installing the batteries Installation Installation Connecting the Repo port Connecting the ground bonding cable Ground bonding cable is not included Connecting the UPS to utility powerConnecting devices to the UPS Installation Starting power to the load Installing the ERMInstallation Installation Modes of operation Standby modeOperate mode UPS operationsExplanation when LED is illuminated Configuring the UPSConfigure mode Auto-Bypass modeAvailable settings Parameter Testing the LEDsVerifying the Repo port connection Silencing an audible alarmPowering down the UPS Power management software Power managementRemoving the UPS front bezel Removing the ERM front bezel MaintenanceReplacing the UPS electronics module Replacing the UPS option card Replacing the batteries Important battery safety informationBattery care and storage guidelines To replace the component, reverse the removal procedureUPS battery replacement procedure Replacing the ERM Replacing the UPSUpdating the UPS firmware 30? TroubleshootingLED and audible alarm troubleshooting Alarm Be silencedInput voltage is not within ±12 percent of nominal voltage Battery conditionGeneral alarm condition Bypass is out of rangeInsufficient warning of low batteries Internal UPS fault conditionLow battery shutdowns Input voltage is out of rangeRepo condition Site wiring conditionUPS does not provide the expected backup time Overload conditionUtility power condition UPS frequently switches between utility and battery powerUPS is in Auto-Bypass mode UPS is on batteryUPS input specifications SpecificationsUPS physical specifications ERM physical specificationsConfiguration setting VAC Available nominal output voltage Power protection specificationsVoltage specifications UPS model Nominal power Rating W Voltage settingOutput tolerance specifications Battery specificationsBattery runtime for NA/JPN model Battery runtime for Intl modelRepo port specifications Environmental specificationsDescription Spare part Number UPS spare parts listSpares Ordering sparesHardware options HP contact information Technical supportBefore you contact HP Pre-Failure Battery Warranty Warranty informationLimited warranty $250,000 Computer Load Protection GuaranteeFederal Communications Commission notice Regulatory compliance noticesRegulatory compliance identification numbers Cables ModificationsEuropean Union regulatory notice Canadian notice Avis CanadienJapanese notice Bsmi notice Battery replacement notice Power cord statement for Japan Taiwan battery recycling noticeGrounding methods to prevent electrostatic discharge Electrostatic dischargePreventing electrostatic discharge Acronyms and abbreviations Index Communications port, connectingInstallation instructions Repo port, connecting

Related manuals

Manual 61 pages 9.34 Kb