HP R5500 manual Repo port, connecting

Page 61

REPO port, connecting 20
REPO port, location	9
REPO port, overview	9
REPO port, specifications 47
REPO port, verifying connection 30
required information	50
required tools 11
runtime specifications	46

S

safety considerations			11, 35
selecting a site	12
series number	52
shipping the UPS		15
site requirements		12
site wiring condition			42
Site Wiring Fault LED, location 8

Site Wiring Fault LED, troubleshooting 39 software 31

spare part numbers 48 spares 48 specifications 44 Standby button, location 7 Standby mode 27

static electricity 57 storing batteries 35 support 50 supported hardware 49 supported software 31

system configuration settings 28

T

Taiwan battery recycling notice 56
technical support	50
telephone numbers	50

temperature ranges (environmental) 47 Test/Alarm Reset button, location 7 testing LEDs 29

tools 11 troubleshooting 39

U

unpacking the components 12 updating the firmware 38 UPS does not start 42

UPS firmware, updating 38 UPS is on battery 43

UPS operations 27 UPS, installing 11, 15

UPS, replacing 37 Utility LED, location 8

Utility LED, troubleshooting 39 utility power condition 43 utility power, connecting 22

V

voltage specifications 45

W

warranties 51

weight, battery 17, 35 weight, ERM 44 weight, UPS 44

Index 61

Image 61

Contents Part Number 351643-004A September 2007 Fourth Edition HP UPS R5500 User GuideAudience assumptions Contents Power management software Verifying the Repo port connection Powering down the UPSOrdering spares Before you contact HP HP contact information UPS spare parts list Hardware optionsUPS R5500 overview Component identificationUPS front panel DescriptionUPS front panel controls Powers up the UPS Starting power toFront panel is shown with the bezel removed LED description UPS front panel LED indicatorsRepo port UPS rear panelERM rear panel Precautions InstallationPreparing to install the hardware Tools and materialsSelecting a site Installing the mounting railsReadying the equipment Installation Installation Preparing the rails for integrated shipping Installing the UPSTighten the hex nuts Installation Removing the UPS battery bracket Installing the batteries Installation Installation Connecting the Repo port Connecting the ground bonding cable Connecting devices to the UPS Connecting the UPS to utility powerGround bonding cable is not included Installation Starting power to the load Installing the ERMInstallation Installation Operate mode Standby modeUPS operations Modes of operationConfigure mode Configuring the UPSAuto-Bypass mode Explanation when LED is illuminatedAvailable settings Parameter Testing the LEDsPowering down the UPS Silencing an audible alarmVerifying the Repo port connection Power management software Power managementRemoving the UPS front bezel Removing the ERM front bezel MaintenanceReplacing the UPS electronics module Replacing the UPS option card Battery care and storage guidelines Important battery safety informationTo replace the component, reverse the removal procedure Replacing the batteriesUPS battery replacement procedure Replacing the ERM Replacing the UPSUpdating the UPS firmware LED and audible alarm troubleshooting TroubleshootingAlarm Be silenced 30?General alarm condition Battery conditionBypass is out of range Input voltage is not within ±12 percent of nominal voltageLow battery shutdowns Internal UPS fault conditionInput voltage is out of range Insufficient warning of low batteriesUPS does not provide the expected backup time Site wiring conditionOverload condition Repo conditionUPS is in Auto-Bypass mode UPS frequently switches between utility and battery powerUPS is on battery Utility power conditionUPS physical specifications SpecificationsERM physical specifications UPS input specificationsVoltage specifications Power protection specificationsUPS model Nominal power Rating W Voltage setting Configuration setting VAC Available nominal output voltageBattery runtime for NA/JPN model Battery specificationsBattery runtime for Intl model Output tolerance specificationsRepo port specifications Environmental specificationsSpares UPS spare parts listOrdering spares Description Spare part NumberHardware options Before you contact HP Technical supportHP contact information Limited warranty Warranty information$250,000 Computer Load Protection Guarantee Pre-Failure Battery WarrantyRegulatory compliance identification numbers Regulatory compliance noticesFederal Communications Commission notice Cables ModificationsEuropean Union regulatory notice Canadian notice Avis CanadienJapanese notice Bsmi notice Battery replacement notice Power cord statement for Japan Taiwan battery recycling noticePreventing electrostatic discharge Electrostatic dischargeGrounding methods to prevent electrostatic discharge Acronyms and abbreviations Index Communications port, connectingInstallation instructions Repo port, connecting

Related manuals

Manual 61 pages 9.34 Kb