HP TippingPoint Next Generation Firewall For information on set net, see set on Related Commands

Page 41

NOTE: You must issue the set net.restart=yes command when you modify the IP address or gateway using the set net command. Changes to these attributes do not take effect until you issue this command. A reboot (reboot command) should be done after you issue the above command.

For information on set net, see ”set ” on page 14.

Related Commands

ifconfig, ipconfig, mgmtsettings

Related Objects dns

Table 3-11 net Attributes

Attribute	Description	Type	Access	Range

net.autoneg	Attribute used to view, and enable/disable	Bool	read-write	0
	auto-negotiation for the Ethernet
	10/100/1000 interface.
	Valid values are: yes or no.

net.duplex	Attribute used to view and change the	String	read-write	4
	duplex setting for the Ethernet
	10/100/1000 interface.
	Valid values are: half or full.

net.gateway	Attribute used to provide the gateway	IPaddr	read-write	0
	(default route) value. To clear this value, use
	a period (.). Applies only the net object.
	The network interface must be restarted
	(net.restart) for setting to take effect. See
	”Example” on page 30.

net.gateway6	Attribute used to provide the IPv6 gateway	IPaddr	read-write	0
	value. To clear this value, use a period (.).
	Applies only the net object.
	The network interface must be restarted
	(net.restart) for setting to take effect. See
	”Example” on page 30.

net.hwaddr	Attribute used to return the Hardware /	String	read-only	17
	MAC (Media Access Control) address for
	the Ethernet10/100/1000 interface.

net.ifc-enable	Attrib used to enable/disable the NIC.	Bool	read-write	0
	Normally, this should not be done. To
	enable the NIC set the value to true, to
	disable the value should be set to false.

net.ipaddr	Attribute used to view and change the IP	IPaddr	read-write	0
	address for the Ethernet10/100/1000
	interface. To clear this value, use a period
	(.). Applies only the net object. The network
	interface must be restarted (net.restart) for
	setting to take effect. When you employ this
	command, the CLI may not reflect the
	change with a confirmation message. See
	”Example” on page 30.

Security Management System CLI Reference 31

Image 41

Contents HP TippingPoint Security Management System CLI Reference Unix is a registered trademark of The Open Group Table of Contents SMS Attributes and Objects List of Tables Page About This Guide Document Conventions Document Messages Customer Support Using the Command Line Interface Remote Paths Help Command Lists all commands, objects, and attributes Cls ClearConsole DateDir FactoryresetDns ExitHelp FtpGet Kbdcfg IfconfigIpconfig Key MgmtsettingsList MonitorPassword NicsettingsNotify NtpPing Ping6 RebootQuit ResolveRestart Service-accessReverse RoutesSet SetupShutdown SnmpSnmp-trap Snmp-requestSnmpwalk SnmpgetSsh TimeTraceroute TouchUsers Update‘read-only’ VersionWho ViewWeb Cli SMS Attributes and ObjectsCtl To set ctl.upgrade-source , this takes Time that the database was String Read-only Re-initialized High availability Health Indication for Celsius Designation KbdLicense Net LogsFor information on set net, see set on Related Commands 11 net Attributes Description Type Access Range Pkg 13 pkg Attributes Description Type Access Range Pwd Radius RadiusPAP, CHAP, MSCHAP, MSCHAP2 EAPMD5 RouteSmtp Route6SHA DES Attrib used to remove an Snmp trap String Write-only TripleDES Examples Snmp.trap-user Svc To true. To disable, set to false Example Sys 24 time Attributes Description Type Access Range SMS Attributes and Objects

Related manuals

Manual 252 pages 61.66 Kb

Manual 68 pages 46.8 Kb

Manual 54 pages 53.98 Kb