HP MicroLogix 1761-NET-ENI manual Safety Considerations

Page 16

2-2Installation and Wiring

Safety Considerations

Tests. For specific information required by EN 61131-2, see the appropriate sections in this publication, as well as the Allen-Bradley publication Industrial Automation Wiring and Grounding Guidelines For Noise Immunity, publication 1770-4.1.

Open style devices must be provided with environmental and safety protection by proper mounting in enclosures designed for specific application conditions. See NEMA Standards publication 250 and IEC publication 529, as applicable, for explanations of the degrees of protection provided by different types of enclosure.

This equipment is suitable for use in Class I, Division 2, Groups A, B, C, D, or non-hazardous locations only. The following WARNING statement applies to use in hazardous locations.

WARNING

!

Explosion Hazard

•Substitution of components may impair suitability for Class I, Division 2.

•Do not replace components or disconnect equipment unless power has been switched off and the area is known to be non-hazardous.

•Do not connect or disconnect connectors or operate switches while circuit is live unless the area is known to be non-hazardous.

•This product must be installed in an enclosure. All cables connected to the product must remain in the enclosure or be protected by conduit or other means.

•The ENI must be operated from an external power source.

•All wiring must comply with N.E.C. article 501-4(b).

Use only the following communication cables and replacement connectors in Class I Division 2 Hazardous Locations.

	Environment Classification	Communication Cable and Connectors

	Class I, Division 2 Hazardous	1761-CBL-PM02 Series C	2707-NC8 Series B
	Environment
	Environment	1761-CBL-HM02 Series C	2707-NC9 Series B
		1761-CBL-HM02 Series C	2707-NC9 Series B

		1761-CBL-AM00 Series C	2707-NC10 Series B

		1761-CBL-AP00 Series C	2707-NC11 Series B

Publication 1761-UM006A-EN-P - February 2001

Image 16

Contents MicroLogix Ethernet Interface ENI Cat. No -NET-ENIAllen-Bradley is a trademark of Rockwell Automation Table of Contents Chapter Preface Who Should Use this ManualRelated Documentation For Read this DocumentTechnical Product Assistance Local Product SupportYour Questions or Comments on this Manual Preface P-4 Publication 1761-UM006A-EN-P January Product Overview Ethernet Connection Non-Ethernet DevicesHardware Features LED IndicatorsProduct Drawing Description Function ColorRS-232 Settings Default Other Options Default SettingsDF1 Settings Default Other Options Operating Modes Device CompatibilityMessaging MailEthernet Networks Using a Web Browser with the ENIBasic Ethernet Topology 6Product Overview Publication 1761-UM006A-EN-P February EMC Directive Low Voltage DirectiveSafety Considerations Mounting DIN Rail MountingPanel Mounting RemovalExternal Power Supply Wiring ENI Port IdentificationEthernet Connections Ethernet 8-Pin 10Base-T Connector PortPin Pin Name Ethernet Cables Maintain ENI ConnectionsRS-232 Connector RS-232 Connector Pin AssignmentsRS-232 Cables ENI Connected to Catalog Number Use CableOperation Overview Number of Connections Dedicated toOutgoing messages Incoming messagesRSLinx on Ethernet PC Connected to Ethernet ENI Functional OverviewOperation 4Operation RSLogix 6Operation ENI Configuration Node 248 to ENI Configuration UtilityCOM Port Settings RS-232 Baud Rate and TCP/IP ParametersMail Settings Save to ENI RAM or ENI ROMReset Message RoutingController Messaging Configuring ENI Data Parameters Target Device Parameters Configuring ENI String Parameters Configuring the ENI E-Mail From StringAlways set this to Node Function Data Type Number Options Default Elements Node 248 Save/Reset Function Save/ResetNode 249 From String ValueNode 250 TCP/IP Configuration TCP/IP Configuration Parameters Function Data Type LengthSubnet Mask is in auto-detect Subnet Mask Auto-Detect OperationSubnet Mask is set to Security Mask Behavior Example Condition Node 251 E-Mail Server Node 252 Bootp ConfigurationNode 253 Baud Rate ENI Baud Rate Options Configuration Value Integer Node 254 Ethernet Hardware AddressPeer-to-Peer Messaging Configuration Node TCP/IP address Message Routing ENI receives read orNode Node100 Node Node101100 Route 0 Address 101 Route 1 Address102 Route 2 Address 103 Route 3 AddressFunction ENI Node DF1 Message Routing148 Use any command supported by your controller Data Table Address Use any valid file Size in ElementsPage Mail Messages Node 50 to OverviewConfiguring E-Mail Smtp E-Mail AddressDestination Addresses Message TextMessage Fields to, from, subject Mail Mail Address Description Message ConfigurationNode Sending an E-Mail Message Mail messages System Diagram Example NetworkPurpose Scope RSLOGIX500131.200.50.95 Example Network IP Addresses Device131.200.50.96 Computer’s Ethernet card Configuring 1761-NET-ENI #1 Throttling Message InstructionsENI #1 Configuration ENI IP Addr Screen Configuring 1761-NET-ENI #2 Message Routing Nodes FunctionENI #2 Configuration RSLogix 5000 Ladder Program ENI #2 Configuration Message Instructions Parameters ENI #2 Configuration Rung Descriptions FunctionMessage Message Function Publication 1761-UM006A-EN-P February ENI #2 Configuration Message ConfigurationTab 10 L20 Controller’s Tags 11 File Mapping in RSLogix Configure Rslinx 1769-L2013 Modify DF1 Parameters Using RSLInx 14 SLC 5/05 Controller Ladder Program 15 SLC 5/05 Rung 0 MSG General Tab 17 SLC 5/05 Rung 1 MSG General Tab 19 ControlLogix 5550 Controller Ladder Program 20 ControlLogix 5550 Rung 0 Message Configuration Tab 22 ControlLogix 5550 Rung 1 Message Configuration Tab Configuring an Ethernet Driver in Rslinx 25 Configure Ethernet Driver Using RSLinx On solid for 2 seconds Power-Up SequenceFlashes for 4 seconds Description Color State Indicates Error Codes Generated by the ENI Message Instruction Error CodesError Code Description of Error Condition Pccc Description Remote station problem due to download Pccc Description Cannot execute command due to active IPBsConnection not completed before user-specified timeout Reply not received before user-specified timeoutPccc Description Command cannot be executed Pccc Description No accessPccc Description Data conversion error Pccc Description Overflow histogram overflow6Troubleshooting Publication 1761-UM006A-EN-P February Description ENI Specification Physical SpecificationsMicroLogix Web Site Mounting Dimensions DimensionsProduct Dimensions TCP/IP Parameters Function Format On the subnet maskGateway Optional1 ZeroUsing Bootp Install the Bootp ServerEdit the Bootp Configuration File Device Name IP Address Hardware Address Ethernet TCP/IPFrom See This platform Executable DOS-basedParameters if necessary Windows Windows Program ManagerRunning the Windows-Based Utility Running the DOS-Based UtilityParameter Description Glossary Node Pccc Programmable Controller Communications Commands RS-232 UTP Unshielded Twisted Pair Allocation of Ethernet connections 3-1Ethernet switch IndexMTA TCP Index Publication 1761-UM006A-EN-P February Page Publication 1761-UM006A-EN-P February