HP Doll c7000 manual Enclosure link cabling, Connector Description

Page 57

Item

Connector

Description

 

 

 

1

OA/iLO

Ethernet 1000BaseT RJ45 connector, which provides Ethernet access to the Onboard

 

 

Administrator and the iLO on each blade. Also supports interconnect modules with

 

 

management processors configured to use the enclosure management network.

 

 

Autonegotiates 1000/100/10 or can be configured to force 100Mb or 10Mb full

 

 

duplex.

 

 

 

2

USB

USB 2.0 Type A connector used for connecting supported USB devices such as DVD

 

 

drives, USB key drives, or a keyboard or mouse for enclosure KVM use. To connect

 

 

multiple devices, a USB hub (not included) is required.

 

 

 

3

Serial connector

Serial RS232 DB-9 connector with PC standard pinout. Connects a computer with a

 

 

null-modem serial cable to the Onboard Administrator command line interface (CLI).

4

VGA connector

VGA DB-15 connector with PC standard pinout. To access the KVM menu or Onboard

 

 

Administrator CLI, connect a VGA monitor or rack KVM monitor for enclosure KVM.

 

 

 

5

Enclosure

Connects to the enclosure link-up port on the enclosure below with a CAT5 patch

 

link-down port

cable

 

 

 

6

Enclosure link-up

Connects to the enclosure link-down port on the enclosure above with a CAT5 patch

 

port and service

cable. On a stand-alone enclosure or the top enclosure in a series of linked

 

port

enclosures, the top enclosure link-up port functions as a service port.

 

 

 

To utilize intelligent power discovery, connect the cables to an intelligent single-phase AC module, and then to the OAs.

This feature is only available on HP BladeSystem c7000 Platinum Enclosures. For more information on intelligent power discovery, see the HP Intelligent Power Distribution Unit User Guide on the HP website (http://www.hp.com/support/manuals).

Enclosure link cabling

Two enclosure link ports are provided on the rear of the enclosure. Link multiple enclosures installed in one rack to:

Allow any active Onboard Administrator module to access the linked enclosures.

Cabling and powering up the enclosure 57

Image 57
Contents HP BladeSystem c7000 Enclosure Setup and Installation Guide Page Contents Support and other resources Contents Verifying the pallet contents Planning the installationRack requirements Rack-free environment requirements Planning the installation Space and airflow requirements Temperature requirements Power requirementsGrounding requirements Enclosure front components Component and LED identificationPower supply bay numbering Power supply LEDs Device bay numbering HP BladeSystem Insight Display components Location Discovery ServicesEnclosure rear components Fan bay numbering Fan LED Onboard Administrator componentsUID LED HP c7000 Onboard Administrator with KVM componentsVGA Interconnect bay numberingInstallation Installation overviewDisassembling the enclosure Installation Installation Rack installation Rack-free installationMeasuring with the rack template Installing the rack railsInstalling the enclosure into the rack Installation Installing the rear cage into the enclosure Installing a power supply Component installationInstallation Installing a full-height blade Installing bladesInstallation Installation Removing a device bay shelf Creating a full-height device bay blank Installation Installing a half-height blade Installation Installation Accessing a server blade with local KVM Accessing local media devices USB diskette drive Description Installing fansInstallation Installing Onboard Administrator modules Installation Installing interconnect modules Installation Mapping to interconnect ports Mapping half-height blades Mapping full-height blades Mapping BL2x220c Blades Mapping the BL680c G7 Blade Bay-to-bay crosslinks Device bay crosslinks Removing interconnect bay dividers Cabling and powering up the enclosure Onboard Administrator cablingCabling the enclosure Enclosure link cabling Connector DescriptionCabling a PC to the enclosure service port Powering up the enclosure Single-phase AC configurationCabling the network to the enclosure Cabling and powering up the enclosure Page PDU installation Cabling and powering up the enclosure Three-phase AC configuration Running the Insight Display installation steps HP BladeSystem Insight DisplayInsight Display overview HP BladeSystem Insight Display HP BladeSystem Insight Display HP BladeSystem Insight Display Navigating the Insight Display Health Summary screen HP BladeSystem Insight Display HP BladeSystem Insight Display Enclosure Info screen Enclosure Settings screenBlade and Port Info screen Turn Enclosure UID On/Off screen HP BladeSystem Insight Display View User Note screen Chat Mode screenTroubleshooting resources TroubleshootingImportant safety information Symbols on equipmentTroubleshooting Power errors Insight Display errorsLocation errors Cooling errorsConfiguration errors Device failure errorsTroubleshooting Before you contact HP Support and other resourcesHP contact information Customer Self RepairRéparation par le client CSR Riparazione da parte del cliente Reparaciones del propio cliente Reparo feito pelo cliente Support and other resources Support and other resources Support and other resources Regulatory compliance notices Regulatory compliance identification numbersFederal Communications Commission notice Modifications CablesCanadian notice Avis Canadien European Union regulatory notice Japanese notice Bsmi notice Korean notice Battery replacement notice Chinese noticeLaser compliance Power cord statement for Japan Taiwan battery recycling noticeElectrostatic discharge Preventing electrostatic dischargeGrounding methods to prevent electrostatic discharge Acronyms and abbreviations USB Documentation feedback Index HP BladeSystem Insight Display errors Static electricity