HP Doll c7000 manual Insight Display errors, Power errors

Page 80

217.7kg

480 lb

WARNING: To reduce the risk of personal injury or damage to the equipment:

Observe local occupation health and safety requirements and guidelines for manual handling.

Obtain adequate assistance to lift and stabilize the chassis during installation or removal.

The server is unstable when not fastened to the rails.

When mounting the server in a rack, remove the power supplies and any other removable module to reduce the overall weight of the product.

CAUTION: To properly ventilate the system, you must provide at least 7.6 cm (3.0 in) of clearance at the front and back of the server.

CAUTION: The server is designed to be electrically grounded (earthed). To ensure proper operation, plug the AC power cord into a properly grounded AC outlet only.

Insight Display errors

The enclosure installation is successful when all errors are corrected. The errors in the following sections are specific to installation and initial configuration of the enclosure. To clear errors that occur after initial powerup and configuration, see the HP BladeSystem Onboard Administrator User Guide for information.

The following types of errors can occur when installing and configuring the enclosure:

Power errors (on page 80)

Cooling errors (on page 81)

Location errors (on page 81)

Configuration errors (on page 81)

Device failure errors (on page 81)

When the enclosure UID LED is off, the Insight Display is illuminated amber when any error condition exists. The navigation bar displays the following selections when an error condition exists:

Health summary icon—Displays the Health Summary screen.

Fix THIS—Suggests corrective action to clear the current error.

Next Alert—Displays the next alert, or if none exist, displays the Health Summary screen.

Previous Alert—Displays the previous alert.

Power errors

Power errors can occur because of insufficient power to bring up an enclosure. Power errors can occur on blades, storage blades, or interconnect modules.

To correct a power error:

1.Use the arrow buttons to navigate to Fix This, and press OK.

2.Review and complete the corrective action suggested by the Insight Display. In most cases, you must either add power supplies to the enclosure or remove the indicated components.

Troubleshooting 80

Image 80
Contents HP BladeSystem c7000 Enclosure Setup and Installation Guide Page Contents Support and other resources Contents Planning the installation Verifying the pallet contentsRack requirements Rack-free environment requirements Planning the installation Space and airflow requirements Grounding requirements Temperature requirementsPower requirements Component and LED identification Enclosure front componentsPower supply bay numbering Power supply LEDs Device bay numbering Location Discovery Services HP BladeSystem Insight Display componentsEnclosure rear components Fan bay numbering Onboard Administrator components Fan LEDHP c7000 Onboard Administrator with KVM components UID LEDInterconnect bay numbering VGADisassembling the enclosure InstallationInstallation overview Installation Installation Rack-free installation Rack installationInstalling the rack rails Measuring with the rack templateInstalling the enclosure into the rack Installation Installing the rear cage into the enclosure Component installation Installing a power supplyInstallation Installing blades Installing a full-height bladeInstallation Installation Removing a device bay shelf Creating a full-height device bay blank Installation Installing a half-height blade Installation Installation Accessing a server blade with local KVM Accessing local media devices Installing fans USB diskette drive DescriptionInstallation Installing Onboard Administrator modules Installation Installing interconnect modules Installation Mapping to interconnect ports Mapping half-height blades Mapping full-height blades Mapping BL2x220c Blades Mapping the BL680c G7 Blade Bay-to-bay crosslinks Device bay crosslinks Removing interconnect bay dividers Cabling the enclosure Cabling and powering up the enclosureOnboard Administrator cabling Connector Description Enclosure link cablingCabling a PC to the enclosure service port Cabling the network to the enclosure Powering up the enclosureSingle-phase AC configuration Cabling and powering up the enclosure Page PDU installation Cabling and powering up the enclosure Three-phase AC configuration Insight Display overview Running the Insight Display installation stepsHP BladeSystem Insight Display HP BladeSystem Insight Display HP BladeSystem Insight Display HP BladeSystem Insight Display Navigating the Insight Display Health Summary screen HP BladeSystem Insight Display HP BladeSystem Insight Display Enclosure Settings screen Enclosure Info screenBlade and Port Info screen Turn Enclosure UID On/Off screen HP BladeSystem Insight Display Chat Mode screen View User Note screenTroubleshooting Troubleshooting resourcesImportant safety information Symbols on equipmentTroubleshooting Insight Display errors Power errorsCooling errors Location errorsConfiguration errors Device failure errorsTroubleshooting Support and other resources Before you contact HPHP contact information Customer Self RepairRéparation par le client CSR Riparazione da parte del cliente Reparaciones del propio cliente Reparo feito pelo cliente Support and other resources Support and other resources Support and other resources Federal Communications Commission notice Regulatory compliance noticesRegulatory compliance identification numbers Canadian notice Avis Canadien ModificationsCables European Union regulatory notice Japanese notice Bsmi notice Korean notice Laser compliance Battery replacement noticeChinese notice Taiwan battery recycling notice Power cord statement for JapanGrounding methods to prevent electrostatic discharge Electrostatic dischargePreventing electrostatic discharge Acronyms and abbreviations USB Documentation feedback Index HP BladeSystem Insight Display errors Static electricity