HP Doll c7000 manual PDU installation

Page 62

minutes to power up, while an enclosure with fewer blades might take less time. Server blades are powered up incrementally, starting from device bay 1.

When first initialized, the Onboard Administrator programs the mezzanine cards on the blades during discovery. After the mezzanine cards are programmed, powering up the enclosure takes only 1 to 2 minutes.

The enclosure and the Insight Display now have power. Configure the enclosure ("Running the Insight Display installation steps" on page 65) using the Insight Display.

PDU installation

The PDU can be installed in either a 1U or a 0U configuration. For more information about installing the PDU in the rack, see the installation instructions that came with the PDU.

IMPORTANT: Rack-based single-phase PDUs cannot be used with a three-phase power configuration.

IMPORTANT: Total VA load of the attached enclosures should not exceed the VA capacity of the PDU. Do not exceed the rated current on circuit breakers.

To connect power to the PDU:

1.Connect the AC power cables to the power connectors on the rear of the enclosure corresponding to the power supply that was populated on the front of the enclosure.

Cabling and powering up the enclosure 62

Image 62
Contents HP BladeSystem c7000 Enclosure Setup and Installation Guide Page Contents Support and other resources Contents Planning the installation Verifying the pallet contentsRack requirements Rack-free environment requirements Planning the installation Space and airflow requirements Grounding requirements Temperature requirementsPower requirements Component and LED identification Enclosure front componentsPower supply bay numbering Power supply LEDs Device bay numbering Location Discovery Services HP BladeSystem Insight Display componentsEnclosure rear components Fan bay numbering Onboard Administrator components Fan LEDHP c7000 Onboard Administrator with KVM components UID LEDInterconnect bay numbering VGADisassembling the enclosure InstallationInstallation overview Installation Installation Rack-free installation Rack installationInstalling the rack rails Measuring with the rack templateInstalling the enclosure into the rack Installation Installing the rear cage into the enclosure Component installation Installing a power supplyInstallation Installing blades Installing a full-height bladeInstallation Installation Removing a device bay shelf Creating a full-height device bay blank Installation Installing a half-height blade Installation Installation Accessing a server blade with local KVM Accessing local media devices Installing fans USB diskette drive DescriptionInstallation Installing Onboard Administrator modules Installation Installing interconnect modules Installation Mapping to interconnect ports Mapping half-height blades Mapping full-height blades Mapping BL2x220c Blades Mapping the BL680c G7 Blade Bay-to-bay crosslinks Device bay crosslinks Removing interconnect bay dividers Cabling the enclosure Cabling and powering up the enclosureOnboard Administrator cabling Connector Description Enclosure link cablingCabling a PC to the enclosure service port Cabling the network to the enclosure Powering up the enclosureSingle-phase AC configuration Cabling and powering up the enclosure Page PDU installation Cabling and powering up the enclosure Three-phase AC configuration Insight Display overview Running the Insight Display installation stepsHP BladeSystem Insight Display HP BladeSystem Insight Display HP BladeSystem Insight Display HP BladeSystem Insight Display Navigating the Insight Display Health Summary screen HP BladeSystem Insight Display HP BladeSystem Insight Display Enclosure Settings screen Enclosure Info screenBlade and Port Info screen Turn Enclosure UID On/Off screen HP BladeSystem Insight Display Chat Mode screen View User Note screenImportant safety information TroubleshootingTroubleshooting resources Symbols on equipmentTroubleshooting Insight Display errors Power errorsConfiguration errors Cooling errorsLocation errors Device failure errorsTroubleshooting HP contact information Support and other resourcesBefore you contact HP Customer Self RepairRéparation par le client CSR Riparazione da parte del cliente Reparaciones del propio cliente Reparo feito pelo cliente Support and other resources Support and other resources Support and other resources Federal Communications Commission notice Regulatory compliance noticesRegulatory compliance identification numbers Canadian notice Avis Canadien ModificationsCables European Union regulatory notice Japanese notice Bsmi notice Korean notice Laser compliance Battery replacement noticeChinese notice Taiwan battery recycling notice Power cord statement for JapanGrounding methods to prevent electrostatic discharge Electrostatic dischargePreventing electrostatic discharge Acronyms and abbreviations USB Documentation feedback Index HP BladeSystem Insight Display errors Static electricity