HP Doll c7000 manual Rack requirements

Page 7

Item	Name	Description

11	Onboard Administrator module	Hot-pluggable enclosure management module. One
		module is required to manage the components
		installed in the enclosure. To provide redundant
		enclosure management, you can install an optional
		second module.

12	Onboard Administrator blank	A mandatory cover installed in any unused Onboard
		Administrator bay
13	Interconnect blank	A mandatory insert installed in any unused
		interconnect bay

14	Interconnect module (quantity and type as	Any of several components, such as pass-thrus or
	ordered)	switches that enable communication between the
		blade and the enclosure

15	Onboard Administrator tray	Hot-pluggable tray that houses up to two Onboard
		Administrator modules and provides two enclosure link
		connectors, the rear enclosure UID, LED, and switch.

16	HP BladeSystem Insight Display	A display that provides information about the health
		and operation of the enclosure
17*	Power retention ties (single-phase enclosures	Tie straps that help prevent single-phase power cables
	only)	from disconnecting from the power connectors

18*	Documentation CD	A CD containing detailed documentation on using the
		enclosure

19*	Hard copy installation instructions for	The printed installation instructions
	blades, options, and interconnects
20*	Installation checklist	A checklist to guide you through installation of the
		enclosure and components

* Not shown

Rack requirements

The enclosure is compatible with the following racks:

•All HP 10000 and 10000G2 Series racks except the HP 10614 rack. NOTE: The system is optimized for 10000 Series racks.

•Telco racks

•Third-party rack cabinets that meet the following requirements: o Width: 48.3 cm (19 in)

o Depth:

—88.9 cm (35 in) maximum clearance between front and rear RETMA rails

—62.7 cm (24.7 in) minimum clearance for round-hole racks

—63.5 cm (25 in) minimum clearance for square-hole racks

oClearance—7.6 cm (3 in) minimum clearance between rear RETMA rails and rear rack door to accommodate system cabling

oClearance—4.5 cm (1.75 in) minimum clearance between rack face and inside of front rack door

Planning the installation 7

Image 7

Contents HP BladeSystem c7000 Enclosure Setup and Installation Guide Page Contents Support and other resources Contents Verifying the pallet contents Planning the installationRack requirements Rack-free environment requirements Planning the installation Space and airflow requirements Power requirements Temperature requirementsGrounding requirements Enclosure front components Component and LED identificationPower supply bay numbering Power supply LEDs Device bay numbering HP BladeSystem Insight Display components Location Discovery ServicesEnclosure rear components Fan bay numbering Fan LED Onboard Administrator componentsUID LED HP c7000 Onboard Administrator with KVM componentsVGA Interconnect bay numberingInstallation overview InstallationDisassembling the enclosure Installation Installation Rack installation Rack-free installationMeasuring with the rack template Installing the rack railsInstalling the enclosure into the rack Installation Installing the rear cage into the enclosure Installing a power supply Component installationInstallation Installing a full-height blade Installing bladesInstallation Installation Removing a device bay shelf Creating a full-height device bay blank Installation Installing a half-height blade Installation Installation Accessing a server blade with local KVM Accessing local media devices USB diskette drive Description Installing fansInstallation Installing Onboard Administrator modules Installation Installing interconnect modules Installation Mapping to interconnect ports Mapping half-height blades Mapping full-height blades Mapping BL2x220c Blades Mapping the BL680c G7 Blade Bay-to-bay crosslinks Device bay crosslinks Removing interconnect bay dividers Onboard Administrator cabling Cabling and powering up the enclosureCabling the enclosure Enclosure link cabling Connector DescriptionCabling a PC to the enclosure service port Single-phase AC configuration Powering up the enclosureCabling the network to the enclosure Cabling and powering up the enclosure Page PDU installation Cabling and powering up the enclosure Three-phase AC configuration HP BladeSystem Insight Display Running the Insight Display installation stepsInsight Display overview HP BladeSystem Insight Display HP BladeSystem Insight Display HP BladeSystem Insight Display Navigating the Insight Display Health Summary screen HP BladeSystem Insight Display HP BladeSystem Insight Display Enclosure Info screen Enclosure Settings screenBlade and Port Info screen Turn Enclosure UID On/Off screen HP BladeSystem Insight Display View User Note screen Chat Mode screenSymbols on equipment TroubleshootingTroubleshooting resources Important safety informationTroubleshooting Power errors Insight Display errorsDevice failure errors Cooling errorsLocation errors Configuration errorsTroubleshooting Customer Self Repair Support and other resourcesBefore you contact HP HP contact informationRéparation par le client CSR Riparazione da parte del cliente Reparaciones del propio cliente Reparo feito pelo cliente Support and other resources Support and other resources Support and other resources Regulatory compliance identification numbers Regulatory compliance noticesFederal Communications Commission notice Cables ModificationsCanadian notice Avis Canadien European Union regulatory notice Japanese notice Bsmi notice Korean notice Chinese notice Battery replacement noticeLaser compliance Power cord statement for Japan Taiwan battery recycling noticePreventing electrostatic discharge Electrostatic dischargeGrounding methods to prevent electrostatic discharge Acronyms and abbreviations USB Documentation feedback Index HP BladeSystem Insight Display errors Static electricity