HP Doll c7000 manual Cabling and powering up the enclosure

Page 60

Single-phase AC configuration using the HP Single-Phase Intelligent Power Module

To cable the enclosure using a single-phase AC configuration:

1.Connect the AC power cables to the power connectors on the rear of the enclosure corresponding to the power supply that was populated on the front of the enclosure.

2.Be sure each power cable is securely attached to the power connectors.

3.Connect the AC power cables to the AC power source or to an installed power distribution unit (PDU).

4.Turn on the AC circuit breakers that power the power cables installed in the enclosure.

5.Locate the power retention bracket that came with the enclosure.

6.Verify that the power cord retention tabs are on the correct side.

o On the left side: To install the power cord retention bracket on the left side of the enclosure, ensure the power cord retention tabs are located to the right of the snap clamps.

o On the right side: To install the power cord retention bracket on the right side of the enclosure, ensure the power cord retention tabs are located on the left side of the snap clamps.

Cabling and powering up the enclosure 60

Image 60
Contents HP BladeSystem c7000 Enclosure Setup and Installation Guide Page Contents Support and other resources Contents Planning the installation Verifying the pallet contentsRack requirements Rack-free environment requirements Planning the installation Space and airflow requirements Temperature requirements Power requirementsGrounding requirements Component and LED identification Enclosure front componentsPower supply bay numbering Power supply LEDs Device bay numbering Location Discovery Services HP BladeSystem Insight Display componentsEnclosure rear components Fan bay numbering Onboard Administrator components Fan LEDHP c7000 Onboard Administrator with KVM components UID LEDInterconnect bay numbering VGAInstallation Installation overviewDisassembling the enclosure Installation Installation Rack-free installation Rack installationInstalling the rack rails Measuring with the rack templateInstalling the enclosure into the rack Installation Installing the rear cage into the enclosure Component installation Installing a power supplyInstallation Installing blades Installing a full-height bladeInstallation Installation Removing a device bay shelf Creating a full-height device bay blank Installation Installing a half-height blade Installation Installation Accessing a server blade with local KVM Accessing local media devices Installing fans USB diskette drive DescriptionInstallation Installing Onboard Administrator modules Installation Installing interconnect modules Installation Mapping to interconnect ports Mapping half-height blades Mapping full-height blades Mapping BL2x220c Blades Mapping the BL680c G7 Blade Bay-to-bay crosslinks Device bay crosslinks Removing interconnect bay dividers Cabling and powering up the enclosure Onboard Administrator cablingCabling the enclosure Connector Description Enclosure link cablingCabling a PC to the enclosure service port Powering up the enclosure Single-phase AC configurationCabling the network to the enclosure Cabling and powering up the enclosure Page PDU installation Cabling and powering up the enclosure Three-phase AC configuration Running the Insight Display installation steps HP BladeSystem Insight DisplayInsight Display overview HP BladeSystem Insight Display HP BladeSystem Insight Display HP BladeSystem Insight Display Navigating the Insight Display Health Summary screen HP BladeSystem Insight Display HP BladeSystem Insight Display Enclosure Settings screen Enclosure Info screenBlade and Port Info screen Turn Enclosure UID On/Off screen HP BladeSystem Insight Display Chat Mode screen View User Note screenTroubleshooting Troubleshooting resourcesImportant safety information Symbols on equipmentTroubleshooting Insight Display errors Power errorsCooling errors Location errorsConfiguration errors Device failure errorsTroubleshooting Support and other resources Before you contact HPHP contact information Customer Self RepairRéparation par le client CSR Riparazione da parte del cliente Reparaciones del propio cliente Reparo feito pelo cliente Support and other resources Support and other resources Support and other resources Regulatory compliance notices Regulatory compliance identification numbersFederal Communications Commission notice Modifications CablesCanadian notice Avis Canadien European Union regulatory notice Japanese notice Bsmi notice Korean notice Battery replacement notice Chinese noticeLaser compliance Taiwan battery recycling notice Power cord statement for JapanElectrostatic discharge Preventing electrostatic dischargeGrounding methods to prevent electrostatic discharge Acronyms and abbreviations USB Documentation feedback Index HP BladeSystem Insight Display errors Static electricity