HP 6000 Router manual LEDs Front Panel of AC Power Module PWR LED description, Led

Page 17

Introduction to General Modules

17

Do not connect the AC power cord while inserting or removing a card.

ON/OFF switch should be set to OFF while inserting or removing.

Figure 6 AC Power

LEDs Figure 7 Front Panel of AC Power Module

Table 8 PWR LED description

LED

Description

 

 

ALM (red)

PWR failure LED. ON means PWR is not in place or has failed.

RUN (green)

PWR operation LED. Constant ON means PWR is operating normally, and

 

OFF means PWR has failed.

AC OK (red)

PWR input LED. Constant ON means the normal voltage (85 ~ 264V) is

 

inputting, and OFF means the voltage input is not normal.

 

 

FAN The 6040 is configured with six fans, separated into three groups. The 6080 is configured with eight fans, separated into four groups. The two fans in a group work in a redundant manner. When all these fans are working normally, the operating temperature of the system can be maintained in the range of 0 to 55 C. Failure of a fan will not affect the operation of other fans, the system will still be able to operate in the normal temperature. The rotating speed of the fans is controlled by the RPU and is in the range of 50% to 100%.

The FAN controller uses two parameters, low-temperature threshold and high-temperature threshold, to control the rotation speed of the fans; the former corresponding to 100% rotating speed, and the latter corresponding to 50% rotating speed. The system will send out rotation stop alarm signals in case any fan fails. The alarm, and state LEDs, of FAN are located on the RPU front panel.

Image 17
Contents Router 6000 Family Installation Guide Campus Drive 3Com CorporationMarlborough, MA 01752-3064Contents Register Your Product to Gain Service Benefits Troubleshooting Application Software UpgradeConventions About this GuideCommunication protocols that are used to interconnect WANs List conventions that are used throughout this guideDocumentation RelatedRouter Use the display user-interfaceIntroduction Main features of 6000 RoutersIntroducing the Router Family Abundant fault isolation methods Structure Router ModelComponents Front PanelRear Panel of the 3Com Router Rear PanelFront Panel Rear Panel of the 3Com Router System Description of 6040 System description6040 6080 SdramIntroduction to Provides the hardware reset button, ResetGeneral Modules 6000 Routers modules include RPU, PSU PWR, FAN, and FICsConsole interface attributes Interface Console interfaceLED and button Description Attribute DescriptionEthernet interface AUX interfaceAUX interface attributes MDILED LEDs Front Panel of AC Power Module PWR LED descriptionFan Location Temperature/Humidity requirements in the equipment room Installing the RouterLimitation on dust content in equipment room General SiteEven the entire Router Check Router Accessories Safety Recommendations3Com 6000 Routers and accessorie Name QuantitySET Installation Tools Meters EquipmentModel Dimensions mm Installation6000 Router dimensions Various FICs Installing ModulesAC power input range 100 to 240V, 50/60Hz AC Connect AC Power Cord AC power supplyCable-retention clip Power switch AC input Recommended AC power socketConnect console cable Console cableAUX cable Console failure, AUX can function as a console interfaceInstalling the Router Configuration Configuring the RouterEstablishing EnvironmentConfiguring the Router Establishing Configuration Environment Configuring the Router Startup Process Self-test on Sdram Select booting device and download applicationsDisplay system information Following information displays on the screenProcedure Router Configuration FundamentalsDecompress Application Initialize the systemSnmp Management Performs the local configuration through CON portSlot 5 Slot 7Slot 8 Slot Interface numbering rule SlotBoot Menu Software MaintenanceSoftware Maintenance Overview Upgrading Boot main system LargeBootrom through serial port Boot Sub-menuStarting Boot main system Modifying serial port parametersStarting application program from Flash Starting host program in default modeEntering serial port sub-menu Entering Ethernet port sub-menu Available Boot Device wancomModifying Flash description area Then the system enters boot file control menuDisplaying available boot files in the Flash Setting the backup boot file Setting the main boot fileAvailable boot files Returning to Boot main menuIgnoring system configuration Upgrading Program Files Using Xmodem ProtocolRebooting the system ProgramXmodem File Setting ParametersUpgrading Building up upgrade environmentApplication Program Via Ethernet PortConfiguring the Router Software Maintenance Power Module Hardware MaintenanceHardware RemovalFan Removal Install a FanRight side inside the integrated chassis Remove a FanRemove an RPU RPU Removal InstallationInstall an RPU Hardware Maintenance Troubleshooting Power System TroubleshootingTroubleshooting Configuration SystemTroubleshooting Troubleshooting Application Software UpgradeUpgrade device of 6000 Router Displays the following promptTroubleshooting Application Software Upgrade Troubleshooting Following are the FICs available for 6000 Series Routers Flexible Interface CardsFIC Categories 3C13861 Port 10/100 FICEthernet Cable Make Ethernet cablePort 100 FX MM FIC 1-port 100BASE-F SM FIC interface attributes SC optical fiber connectorFIC 3C13864 Port Enhanced SerialFIC 3C13863 24 RS232 DTE 24 RS232 DCE 35 DTE 35 DCE 21 DTE 21 DCE Port FICAttribute Description Synchronous Asychronous DTE, DCEService Terminal accessFront panel of 8-port FIC is shown as follows DDN leased linePort Fractional FIC Connecting the Interface CableInterface Attributes Port Channelized FIC E1 FIC Data is being transceived Following table describes the LEDs on the card panelsLEDs on the Card Panel 120-ohm 4E1 adapter cable Interface cables Internal DIP SwitchPort Channelized T1/PRI FIC Port Fractional T1 FICPort Channelized T1/PRI FIC panel Interface attributes of FICcardsMain functions of 1-port Channelized E3 FIC include Port Channelized E3 FIC 3C13888Interface Attributes Port Channelized E3 FIC Interface attributesMain functions of 1-port Channelized T3 FIC include Port Channelized T3 1CT3 3C13889Connect Interface Cable Port T3 interface attributes Following table describes the LEDs on the card panelLED description of 1-port T3 FIC CT3Port OC ATM Attribute Port OC-3 ATM SML Following figure illustrates the 1-port OC-3 ATM SM panelSonet OC-3/SDHPots FIC 3C13872 Port Adsl overFollowing figure illustrates the 1-port OC-3 ATM SML panel LED description of the ATM cardsFIC-1ADSL Port Adsl FIC interface attributesAttribute Port Adsl FIC Pstnm LED description 2-port Adsl FICFlexible Interface Cards Obtaining Support for Your Product Support and Repair Contact UsTelephone Technical US and Canada Telephone Technical Support and Repair Latin America Telephone Technical Support and RepairAppendix a Obtaining Support for Your Product