HP 6000 Router manual Hardware Maintenance

Page 52

52CHAPTER 5: HARDWARE MAINTENANCE

Image 52
Contents Router 6000 Family Installation Guide 3Com Corporation Campus DriveMarlborough, MA 01752-3064Contents Troubleshooting Application Software Upgrade Register Your Product to Gain Service BenefitsAbout this Guide ConventionsCommunication protocols that are used to interconnect WANs List conventions that are used throughout this guideRelated DocumentationRouter Use the display user-interfaceIntroducing the Router Family Main features of 6000 RoutersIntroduction Abundant fault isolation methods Router Model StructureComponents Front PanelRear Panel Rear Panel of the 3Com RouterFront Panel Rear Panel of the 3Com Router System description System Description of 60406040 6080 SdramProvides the hardware reset button, Reset Introduction toGeneral Modules 6000 Routers modules include RPU, PSU PWR, FAN, and FICsInterface Console interface Console interface attributesLED and button Description Attribute DescriptionAUX interface Ethernet interfaceAUX interface attributes MDILEDs Front Panel of AC Power Module PWR LED description LEDFan Location Installing the Router Temperature/Humidity requirements in the equipment roomLimitation on dust content in equipment room General SiteEven the entire Router Safety Recommendations Check Router Accessories3Com 6000 Routers and accessorie Name QuantityInstallation Tools Meters Equipment SET6000 Router dimensions InstallationModel Dimensions mm Installing Modules Various FICsConnect AC Power Cord AC power supply AC power input range 100 to 240V, 50/60Hz ACCable-retention clip Power switch AC input Recommended AC power socketConsole cable Connect console cableConsole failure, AUX can function as a console interface AUX cableInstalling the Router Configuring the Router ConfigurationEstablishing EnvironmentConfiguring the Router Establishing Configuration Environment Configuring the Router Select booting device and download applications Startup Process Self-test on SdramDisplay system information Following information displays on the screenRouter Configuration Fundamentals ProcedureDecompress Application Initialize the systemPerforms the local configuration through CON port Snmp ManagementSlot Slot 5 Slot 7Slot 8 Slot Interface numbering ruleSoftware Maintenance Overview Software MaintenanceBoot Menu Boot Sub-menu Upgrading Boot main system LargeBootrom through serial portStarting Boot main system Modifying serial port parametersStarting host program in default mode Starting application program from FlashEntering serial port sub-menu Available Boot Device wancom Entering Ethernet port sub-menuDisplaying available boot files in the Flash Then the system enters boot file control menuModifying Flash description area Setting the main boot file Setting the backup boot fileAvailable boot files Returning to Boot main menuUpgrading Program Files Using Xmodem Protocol Ignoring system configurationRebooting the system ProgramSetting Parameters Xmodem FileBuilding up upgrade environment UpgradingApplication Program Via Ethernet PortConfiguring the Router Software Maintenance Hardware Maintenance Power ModuleHardware RemovalInstall a Fan Fan RemovalRight side inside the integrated chassis Remove a FanInstall an RPU RPU Removal InstallationRemove an RPU Hardware Maintenance Troubleshooting Troubleshooting Power SystemTroubleshooting Configuration SystemTroubleshooting Application Software Upgrade TroubleshootingUpgrade device of 6000 Router Displays the following promptTroubleshooting Application Software Upgrade Troubleshooting FIC Categories Flexible Interface CardsFollowing are the FICs available for 6000 Series Routers Port 10/100 FIC 3C13861Make Ethernet cable Ethernet CablePort 100 FX MM FIC SC optical fiber connector 1-port 100BASE-F SM FIC interface attributesFIC 3C13863 Port Enhanced SerialFIC 3C13864 Port FIC 24 RS232 DTE 24 RS232 DCE 35 DTE 35 DCE 21 DTE 21 DCEAttribute Description Synchronous Asychronous DTE, DCETerminal access ServiceFront panel of 8-port FIC is shown as follows DDN leased lineInterface Attributes Port Channelized FIC Connecting the Interface CablePort Fractional FIC E1 FIC LEDs on the Card Panel Following table describes the LEDs on the card panelsData is being transceived 120-ohm 4E1 adapter cable Internal DIP Switch Interface cablesPort Channelized T1/PRI FIC Port Fractional T1 FICInterface attributes of FICcards Port Channelized T1/PRI FIC panelPort Channelized E3 FIC 3C13888 Main functions of 1-port Channelized E3 FIC includeInterface Attributes Port Channelized E3 FIC Interface attributesConnect Interface Cable Port Channelized T3 1CT3 3C13889Main functions of 1-port Channelized T3 FIC include Following table describes the LEDs on the card panel Port T3 interface attributesLED description of 1-port T3 FIC CT3Following figure illustrates the 1-port OC-3 ATM SM panel Port OC ATM Attribute Port OC-3 ATM SMLSonet OC-3/SDHPort Adsl over Pots FIC 3C13872Following figure illustrates the 1-port OC-3 ATM SML panel LED description of the ATM cardsAttribute Port Adsl FIC Port Adsl FIC interface attributesFIC-1ADSL LED description 2-port Adsl FIC PstnmFlexible Interface Cards Obtaining Support for Your Product Telephone Technical Contact UsSupport and Repair Latin America Telephone Technical Support and Repair US and Canada Telephone Technical Support and RepairAppendix a Obtaining Support for Your Product