HP 6000 Router Starting host program in default mode, Starting application program from Flash

Page 39

Software Maintenance Overview

39

Boot Main Menu The following is prompted on the terminal screen after the system enters Boot main system.

Copyright(C) 2001-2004 by 3Com Corporation CO.

Creation date: Jul 14 2003, 10:54:22

CPU type		: IBM750FX-DD2.2
CPU L2	Cache	: 512KB
CPU Clock Speed		: 625MHz
BUS Clock Speed		: 125MHz
Memory	Size	: 256MB
Press Ctrl+B	to enter	Boot Menu... 0

If you press <Ctrl+B> at this time, the system will enter Boot main menu.

Press <Ctrl+B> four seconds after startup to enter Boot main menu. Otherwise the system will start host program in default mode.

The system will first prompt the following information for you to enter the password. If the password is correct, the system shows the main menu. If you enter an incorrect password three times consecutively, the system restarts.

MAIN MENU

=====================<MAIN-BOOTROM MENU>======================= <1> Boot With Default Mode

<2> Boot From Flash

<3> Enter Serial SubMenu <4> Enter Ethernet SubMenu <5> Modify Bootrom Password <6> Reboot

===============================================================

Enter your choice(1-7): _

If you use Flash for the first time, and reading or writing Flash is required, Flash will be formatted first. Then the following information will be prompted:

Formatting Flash, please waiting several minutes...done

Starting host program in default mode

Enter <1> in Boot main menu and the system will first read, Flash description area to get start flag (from Flash or from hardware disk) and start file names. Then it downloads host program files to memory as per start flag and start file names. The system decompresses and starts the files, and the terminal will display:

Boot With Default Mode

Booting From Flash...

The Boot File is < flash:/6080.bin >

The Router 6000 only supports starting Boot main menu from Flash.

Starting application program from Flash

Enter <2> in Boot main menu and the system will first read Flash description area to get Flash start file names. Then it downloads host program files to memory as per start file names. The system decompresses and starts the files. The following information is prompted on the terminal screen:

Image 39

Contents Router 6000 Family Installation Guide 01752-3064 3Com CorporationCampus Drive Marlborough, MAContents Register Your Product to Gain Service Benefits Troubleshooting Application Software UpgradeList conventions that are used throughout this guide About this GuideConventions Communication protocols that are used to interconnect WANsUse the display user-interface RelatedDocumentation RouterMain features of 6000 Routers Introducing the Router FamilyIntroduction Abundant fault isolation methods Front Panel Router ModelStructure ComponentsRear Panel of the 3Com Router Rear PanelFront Panel Rear Panel of the 3Com Router Sdram System descriptionSystem Description of 6040 6040 60806000 Routers modules include RPU, PSU PWR, FAN, and FICs Provides the hardware reset button, ResetIntroduction to General ModulesAttribute Description Interface Console interfaceConsole interface attributes LED and button DescriptionMDI AUX interfaceEthernet interface AUX interface attributesLED LEDs Front Panel of AC Power Module PWR LED descriptionFan Location General Site Installing the RouterTemperature/Humidity requirements in the equipment room Limitation on dust content in equipment roomEven the entire Router Name Quantity Safety RecommendationsCheck Router Accessories 3Com 6000 Routers and accessorieSET Installation Tools Meters EquipmentInstallation 6000 Router dimensionsModel Dimensions mm Various FICs Installing ModulesRecommended AC power socket Connect AC Power Cord AC power supplyAC power input range 100 to 240V, 50/60Hz AC Cable-retention clip Power switch AC inputConnect console cable Console cableAUX cable Console failure, AUX can function as a console interfaceInstalling the Router Environment Configuring the RouterConfiguration EstablishingConfiguring the Router Establishing Configuration Environment Configuring the Router Following information displays on the screen Select booting device and download applicationsStartup Process Self-test on Sdram Display system informationInitialize the system Router Configuration FundamentalsProcedure Decompress ApplicationSnmp Management Performs the local configuration through CON portSlot 5 Slot 7Slot 8 Slot Interface numbering rule SlotSoftware Maintenance Software Maintenance OverviewBoot Menu Modifying serial port parameters Boot Sub-menuUpgrading Boot main system LargeBootrom through serial port Starting Boot main systemStarting application program from Flash Starting host program in default modeEntering serial port sub-menu Entering Ethernet port sub-menu Available Boot Device wancomThen the system enters boot file control menu Displaying available boot files in the FlashModifying Flash description area Returning to Boot main menu Setting the main boot fileSetting the backup boot file Available boot filesProgram Upgrading Program Files Using Xmodem ProtocolIgnoring system configuration Rebooting the systemXmodem File Setting ParametersVia Ethernet Port Building up upgrade environmentUpgrading Application ProgramConfiguring the Router Software Maintenance Removal Hardware MaintenancePower Module HardwareRemove a Fan Install a FanFan Removal Right side inside the integrated chassisRPU Removal Installation Install an RPURemove an RPU Hardware Maintenance Configuration System TroubleshootingTroubleshooting Power System TroubleshootingDisplays the following prompt Troubleshooting Application Software UpgradeTroubleshooting Upgrade device of 6000 RouterTroubleshooting Application Software Upgrade Troubleshooting Flexible Interface Cards FIC CategoriesFollowing are the FICs available for 6000 Series Routers 3C13861 Port 10/100 FICEthernet Cable Make Ethernet cablePort 100 FX MM FIC 1-port 100BASE-F SM FIC interface attributes SC optical fiber connectorPort Enhanced Serial FIC 3C13863FIC 3C13864 DTE, DCE Port FIC24 RS232 DTE 24 RS232 DCE 35 DTE 35 DCE 21 DTE 21 DCE Attribute Description Synchronous AsychronousDDN leased line Terminal accessService Front panel of 8-port FIC is shown as followsConnecting the Interface Cable Interface Attributes Port Channelized FICPort Fractional FIC E1 FIC Following table describes the LEDs on the card panels LEDs on the Card PanelData is being transceived 120-ohm 4E1 adapter cable Port Fractional T1 FIC Internal DIP SwitchInterface cables Port Channelized T1/PRI FICPort Channelized T1/PRI FIC panel Interface attributes of FICcardsPort Channelized E3 FIC Interface attributes Port Channelized E3 FIC 3C13888Main functions of 1-port Channelized E3 FIC include Interface AttributesPort Channelized T3 1CT3 3C13889 Connect Interface CableMain functions of 1-port Channelized T3 FIC include CT3 Following table describes the LEDs on the card panelPort T3 interface attributes LED description of 1-port T3 FICOC-3/SDH Following figure illustrates the 1-port OC-3 ATM SM panelPort OC ATM Attribute Port OC-3 ATM SML SonetLED description of the ATM cards Port Adsl overPots FIC 3C13872 Following figure illustrates the 1-port OC-3 ATM SML panelPort Adsl FIC interface attributes Attribute Port Adsl FICFIC-1ADSL Pstnm LED description 2-port Adsl FICFlexible Interface Cards Obtaining Support for Your Product Contact Us Telephone TechnicalSupport and Repair US and Canada Telephone Technical Support and Repair Latin America Telephone Technical Support and RepairAppendix a Obtaining Support for Your Product