HP 6000 Router manual Hardware Maintenance, Power Module, Removal

Page 49

5

HARDWARE MAINTENANCE

Hardware	Please review the following cautions before installation or maintenance:
Maintenance	■ On a mounting screw of 3Com 6000 series router chassis, there is an

	anti-dismantle seal of 3Com Corporation. The seal must be kept intact
	before the support agent performs maintenance on the switch.
	■ Remember to wear ESD-preventive wrist strap.

Power Module	6000 Series Routers support 1+1 redundant power system. The power modules
Removal and	are hot-swappable.
Installation

Remove a Power

Module

1Turn off power switch.

2Remove the power cord connected to the power module to be removed and loosen the two captive screws in the top panel of the module.

3Hold the handle of the module and gently pull the module out along the guides.

Figure 1 Power Module Removal

Install a Power Module

1Hold the handle of the power module panel, slowly push the module into the chassis along the guides until it touches the rear power panel inside the power slot of the chassis.

2Fasten the two captive screws in the power module panel.

Image 49

Contents Router 6000 Family Installation Guide Campus Drive 3Com CorporationMarlborough, MA 01752-3064Contents Register Your Product to Gain Service Benefits Troubleshooting Application Software UpgradeConventions About this GuideCommunication protocols that are used to interconnect WANs List conventions that are used throughout this guideDocumentation RelatedRouter Use the display user-interfaceIntroducing the Router Family Main features of 6000 RoutersIntroduction Abundant fault isolation methods Structure Router ModelComponents Front PanelRear Panel of the 3Com Router Rear PanelFront Panel Rear Panel of the 3Com Router System Description of 6040 System description6040 6080 SdramIntroduction to Provides the hardware reset button, ResetGeneral Modules 6000 Routers modules include RPU, PSU PWR, FAN, and FICsConsole interface attributes Interface Console interfaceLED and button Description Attribute DescriptionEthernet interface AUX interfaceAUX interface attributes MDILED LEDs Front Panel of AC Power Module PWR LED descriptionFan Location Temperature/Humidity requirements in the equipment room Installing the RouterLimitation on dust content in equipment room General SiteEven the entire Router Check Router Accessories Safety Recommendations3Com 6000 Routers and accessorie Name QuantitySET Installation Tools Meters Equipment6000 Router dimensions InstallationModel Dimensions mm Various FICs Installing ModulesAC power input range 100 to 240V, 50/60Hz AC Connect AC Power Cord AC power supplyCable-retention clip Power switch AC input Recommended AC power socketConnect console cable Console cableAUX cable Console failure, AUX can function as a console interfaceInstalling the Router Configuration Configuring the RouterEstablishing EnvironmentConfiguring the Router Establishing Configuration Environment Configuring the Router Startup Process Self-test on Sdram Select booting device and download applicationsDisplay system information Following information displays on the screenProcedure Router Configuration FundamentalsDecompress Application Initialize the systemSnmp Management Performs the local configuration through CON portSlot 5 Slot 7Slot 8 Slot Interface numbering rule SlotSoftware Maintenance Overview Software MaintenanceBoot Menu Upgrading Boot main system LargeBootrom through serial port Boot Sub-menuStarting Boot main system Modifying serial port parametersStarting application program from Flash Starting host program in default modeEntering serial port sub-menu Entering Ethernet port sub-menu Available Boot Device wancomDisplaying available boot files in the Flash Then the system enters boot file control menuModifying Flash description area Setting the backup boot file Setting the main boot fileAvailable boot files Returning to Boot main menuIgnoring system configuration Upgrading Program Files Using Xmodem ProtocolRebooting the system ProgramXmodem File Setting ParametersUpgrading Building up upgrade environmentApplication Program Via Ethernet PortConfiguring the Router Software Maintenance Power Module Hardware MaintenanceHardware RemovalFan Removal Install a FanRight side inside the integrated chassis Remove a FanInstall an RPU RPU Removal InstallationRemove an RPU Hardware Maintenance Troubleshooting Power System TroubleshootingTroubleshooting Configuration SystemTroubleshooting Troubleshooting Application Software UpgradeUpgrade device of 6000 Router Displays the following promptTroubleshooting Application Software Upgrade Troubleshooting FIC Categories Flexible Interface CardsFollowing are the FICs available for 6000 Series Routers 3C13861 Port 10/100 FICEthernet Cable Make Ethernet cablePort 100 FX MM FIC 1-port 100BASE-F SM FIC interface attributes SC optical fiber connectorFIC 3C13863 Port Enhanced SerialFIC 3C13864 24 RS232 DTE 24 RS232 DCE 35 DTE 35 DCE 21 DTE 21 DCE Port FICAttribute Description Synchronous Asychronous DTE, DCEService Terminal accessFront panel of 8-port FIC is shown as follows DDN leased lineInterface Attributes Port Channelized FIC Connecting the Interface CablePort Fractional FIC E1 FIC LEDs on the Card Panel Following table describes the LEDs on the card panelsData is being transceived 120-ohm 4E1 adapter cable Interface cables Internal DIP SwitchPort Channelized T1/PRI FIC Port Fractional T1 FICPort Channelized T1/PRI FIC panel Interface attributes of FICcardsMain functions of 1-port Channelized E3 FIC include Port Channelized E3 FIC 3C13888Interface Attributes Port Channelized E3 FIC Interface attributesConnect Interface Cable Port Channelized T3 1CT3 3C13889Main functions of 1-port Channelized T3 FIC include Port T3 interface attributes Following table describes the LEDs on the card panelLED description of 1-port T3 FIC CT3Port OC ATM Attribute Port OC-3 ATM SML Following figure illustrates the 1-port OC-3 ATM SM panelSonet OC-3/SDHPots FIC 3C13872 Port Adsl overFollowing figure illustrates the 1-port OC-3 ATM SML panel LED description of the ATM cardsAttribute Port Adsl FIC Port Adsl FIC interface attributesFIC-1ADSL Pstnm LED description 2-port Adsl FICFlexible Interface Cards Obtaining Support for Your Product Telephone Technical Contact UsSupport and Repair US and Canada Telephone Technical Support and Repair Latin America Telephone Technical Support and RepairAppendix a Obtaining Support for Your Product