Pelco es3012 installation manual Accessing Main Menu Preset

Page 17

ACCESSING MAIN MENU (PRESET 95)

You can call up the main menu on your monitor by programming (setting or creating) preset 95 (28 if in 32-preset mode).

Programming preset 95 for Pelco’s controllers varies according to the type of controller you are using. Instructions for programming preset 95 are given below for various Pelco control- lers.

CM6700

1.Enter the number of the camera and press the CAM key.

2.Enter 95 and hold the PRESET key for two seconds.

3.In the Edit Preset menu, arrow to SET and press the ACK key. The main menu ap- pears.

KBD200/KBD300/KBD300V (Direct Mode Only)

1.Enter 95.

2.Hold the PRESET key (approximately 5 seconds) until the main menu appears on the screen.

CM8500

1.Enter the number of the camera and press the CAM key.

2.Highlight PRESET in the Camera menu and hold down the joystick button until the Set Presets prompt appears.

3.Enter 95 and press the PRESET key. The text editor appears. Select ENTER and the main menu appears.

CM9500

1.Enter the number of the camera and press the CAM key. The Main menu appears.

2.Highlight SETUP in the Main menu and press the SELECT key.

3.Highlight CAM in the Setup menu and press the SELECT key.

4.Highlight PRESET in the Camera menu and press the SELECT key.

5.Enter 95 and press the F1 key. The main menu appears.

CM9750

1.Turn the KEY SWITCH to the ON position.

2.Press the PROG key. PROGRAM appears on the LCD display.

3.Press the PRES key. The PRESET prompt appears.

4.Enter 95 and press the ENTER key. The main menu appears.

5.Turn the KEY SWITCH to the OFF position.

CM9740/CM9760/CM9770

1.Press the ESCAPE key to open the Main menu. Select DEF. The Define Submenu appears.

2.Enter your four-digit PIN if this is your first time entering this mode.

3.Enter 95 and select PRST. The main menu appears on the monitor.

4.Select the Quit icon to return to the default menu.

KBD4000/KBD4002/KBD4000V

1.Press the SPOT MONITOR key.

2.Enter 95, then hold the PRESET key (approximately 5 seconds) until the main menu appears on the screen.

MPT9500

Standard Coaxitron Mode

1.Enter 95 and press the PRESET SET key.

2.Position the asterisk in the YES row and press the F1 key. The main menu appears.

Extended Coaxitron or RS-485 Mode

1.Enter 95 and press the PRESET SET key.

2.Press the F2 key. The main menu appears.

Pelco Manual C306M-K (4/05)

17

Image 17
Contents ES3012 Series Esprit Pelco Manual C306M-K 4/05 Contents List of Tables Esprit ES3012 System Dimensions DrawingList of Illustrations Important Safety Instructions Basic DescriptionModels Camera and Lens Installation InstallationPIN Holder PAN and Tilt Installation RX+ Pelco Manual C306M-K 4/05 HOW to Remove the PAN and Tilt Cover TXB Series Translator Board Installation OptionalHOW to Reinstall the PAN and Tilt Cover HOW to Operate Your Esprit Integrated Positioning System POWER-UP DisplayOperation Operating Notes Environmental RangePAN, SCAN, and Tilt Speeds Preset FunctionsLens Functions RANDOM, FRAME, and Auto ScanningEsprit Menus PresetsProgramming Accessing Main Menu Preset AZ/EL AZ/EL Line Azimuth Zero Direction Direction Line Display Duration Programming Limit Stops Limit Stops Turning Limit Stops on or OFFScan Limit Stops Pattern Length PAN/SCAN SpeedPark Time POWER-UP Mode Speed Profile Other Menu Zone BlankSymptom System does not operate TroubleshootingSymptom No control/sluggish control Coaxitron Symptom No control RS-422Symptom No video or poor video MaintenanceBaud Rate Switch Setting SW1-4 SW1-5Appendix Table B. Switch Settings for SW2 112 232 Electrical SpecificationsALL Others are Inches Regulatory Notices Product Warranty and Return Information ISO9001