Pelco es3012 installation manual PAN/SCAN Speed, Park Time, Pattern Length

Page 26

PAN/SCAN SPEED

The pan/scan speed is adjustable from 3-40 degrees per second. This occurs in three scan modes: auto, random, and frame scan.

To change the pan/scan speed:

1.Program preset 95 (28). The main menu appears.

2.Position the cursor (>) beside Other.

3.Press the Iris Open button to enter the Other menu.

4.Position the cursor (>) beside Pan/Scan Spd.

5.Press the Iris Open button. The cursor moves to the right beside the number of degrees.

6.Move the joystick up or down to toggle through the number of degrees (3-40) until you reach the number you want. (If set on a low number, the scan appears to barely move but is still functioning.)

7.SELECT - Press the Iris Open button on your keyboard to select your choice. CANCEL - Press the Iris Close button if you do not want to change the setting.

PARK TIME

NOTE: Preset 1 must be programmed for the system to park.

This feature causes the pan and tilt to park at preset 1 after a programmed number of min- utes of control inactivity. The time can be set from 1 minute to 720 minutes (12 hours), or it can be set to zero, which disables this feature.

To change the park time:

1.Program preset 95 (28). The main menu appears.

2.Position the cursor (>) beside Other.

3.Press the Iris Open button to enter the Other menu.

4.Position the cursor (>) beside Park Time.

5.Press the Iris Open button. The cursor moves to the right beside the current park time.

6.Move the joystick up or down to change the park time.

7.SELECT - Press the Iris Open button on your keyboard to select your choice. CANCEL - Press the Iris Close button if you do not want to change the setting.

PATTERN LENGTH

CAUTION: If the length is changed, all stored patterns

are erased.

The system can do either:

One full pattern - 1.5, 3, or 6 minutes long or

Two half patterns - .75, 1.5, or 3 minutes long

To set the pattern length:

1.Program preset 95 (28). The main menu appears.

2.Position the cursor (>) beside Other.

3.Press the Iris Open button to enter the Other menu.

4.Position the cursor (>) beside Pat Length.

5.Press the Iris Open button. The cursor moves to the right, beside the number of minutes (1.5, 3, or 6).

6.Move the joystick up or down to toggle through the number of minutes (1.5, 3, or 6).

7.SELECT - Press the Iris Open button on your keyboard to select your choice. CANCEL - Press the Iris Close button if you do not want to change the setting.

26

Pelco Manual C306M-K (4/05)

Image 26
Contents ES3012 Series Esprit Pelco Manual C306M-K 4/05 Contents List of Tables Esprit ES3012 System Dimensions DrawingList of Illustrations Important Safety Instructions Basic DescriptionModels Installation Camera and Lens InstallationPIN Holder PAN and Tilt Installation RX+ Pelco Manual C306M-K 4/05 TXB Series Translator Board Installation Optional HOW to Remove the PAN and Tilt CoverHOW to Reinstall the PAN and Tilt Cover Operation POWER-UP DisplayHOW to Operate Your Esprit Integrated Positioning System Operating Notes Environmental RangeLens Functions Preset FunctionsPAN, SCAN, and Tilt Speeds RANDOM, FRAME, and Auto ScanningEsprit Menus PresetsProgramming Accessing Main Menu Preset AZ/EL AZ/EL Line Azimuth Zero Direction Direction Line Display Duration Limit Stops Turning Limit Stops on or OFF Programming Limit StopsScan Limit Stops Pattern Length PAN/SCAN SpeedPark Time POWER-UP Mode Speed Profile Zone Blank Other MenuSymptom No control/sluggish control Coaxitron TroubleshootingSymptom System does not operate Symptom No control RS-422Maintenance Symptom No video or poor videoBaud Rate Switch Setting SW1-4 SW1-5Appendix Table B. Switch Settings for SW2 112 232 Specifications ElectricalALL Others are Inches Regulatory Notices Product Warranty and Return Information ISO9001