Pelco c1487-c operation manual Main Menu Access, Backlight Compensation

Page 29

NON-SENSITIVE AREA

SENSITIVE

AREA

Figure 17. Backlight

Compensation

MAIN MENU ACCESS

You can call up the main menu on your monitor by programming (setting or creating) preset 95 (28 if in 32-preset mode; refer to the Preset Functions section).

Programming preset 95 for Pelco’s controllers varies according to the type of controller you are using. Instructions for programming preset 95 are given below for various Pelco controllers.

CM6700

1.Enter the number of the Spectra II™ or Spectra Lite™ camera and press the CAM key.

2.Enter 95 and hold the PRESET key for two seconds.

3.In the Edit Preset menu, arrow to SET and press the ACK key. The main menu appears.

CM8500

1.Enter the number of the Spectra II™ or Spectra Lite™ camera and press the CAM key.

2.Highlight PRESET in the Camera menu and hold down the joystick button until the Set Presets prompt appears.

3.Enter 95 and press the PRESET key. The main menu appears.

CM9500

1.Enter the number of the Spectra II™ or Spectra Lite™ camera and press the CAM key.

2.Press the SELECT key twice.

3.Highlight CAM in the Setup menu and press the SELECT key.

4.Highlight PRESET in the Camera menu and press the SELECT key.

5.Enter 95 and press the F1 key. The main menu appears.

CM9750

1.Turn the KEY SWITCH to the ON position.

2.Press the PROG key. PROGRAM appears on the LCD display.

3.Press the PRES key. The PRESET prompt appears.

4.Enter 95 and press the ENTER key. The main menu appears.

5.Turn the KEY SWITCH to the OFF position.

CM9760

1.In the default menu, select DEF. The Define Submenu appears.

2.Enter your four-digit PIN.

3.Enter 95 and select PRST. The main menu appears on the monitor.

4.Select the Quit icon to return to the default menu.

MPT9500

Standard Coaxitron® Mode

1.Enter 95 and press the PRESET SET key.

2.Position the asterisk in the YES row and press the F1 key. The main menu appears.

Extended Coaxitron® or RS-485 Mode

1.Enter 95 and press the PRESET SET key.

2.Press the F2 key. The main menu appears.

BACKLIGHT COMPENSATION

There are two backlight compensation modes: on and off.

Backlight compensation allows the Spectra II™ dome to compensate for bright light behind the object you want to view. With backlight compensation On, the Spectra II™ dome will use only the center 10 percent of the picture for adjusting the iris (refer to Figure 17). If there is a bright light source outside of this area, it will wash out to white. The camera will adjust the iris so that the object in the sensitive area is properly exposed.

To change the backlight compensation mode:

1.Program Preset 95 (28 if in 32-preset mode; refer to the Preset Functions section) to access the main menu (refer to the Main Menu Access section). The main menu will appear.

2.If the cursor (>) is not beside Camera, move the joystick up or down to position the cursor beside Camera.

Pelco Manual C1487M-C (7/99)

29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Listed Contents List of Tables List of IllustrationsMeasures DE Securite Importantes Important Safeguards and WarningsGeneral Back Box IN-CEILING ModelsDome Drive Lower DomePendant Components Pendant ModelsModels DescriptionSpectra II Pendant Components Spectra II IN-CEILING ComponentsSpectra Lite Pendant Components Installation for IN-CEILING ModelsSpectra Lite IN-CEILING Components Ceiling and Back BOX PreparationSuspended Ceiling Installing Back BoxWiring Diagram for Spectra WiringRG6/U Cable Type Maximum DistanceTable B VAC Wiring Distances Back BOX InstallationBack BOX Connections From controller To 4-Wire terminal on circuit boardControl Dome Drive Switch Locations Table C. Switch Settings for SW1For D-type control systems, refer to Table E Baud Rate Switch Setting SW2-6 SW2-7 SW2-8For P-type control systems, refer to Table D 100 117 177 Lower Dome Lower Dome Installation, In-Ceiling ModelsPENDANT-MOUNT Installation Installation for Pendant ModelsOperation SURFACE-MOUNT InstallationPAN and Tilt Functions POWER-UP DisplayAuto Flip Scan SpeedSpectra Lite Zoom Preset FunctionsZoom Spectra II Zoom RANDOM, FRAME, and Auto Scanning AlarmsZones PatternsPark Auxiliary OutputsProgramming the Spectra II and Spectra Lite Backlight Compensation Main Menu AccessDenotes items that apply to the Spectra II only Reset CameraZoom Limit GAIN/AGC AGC ModeAuto Iris GainShutter Speed Sharpness AUTO-FOCUS ModeLine Synchronization White Balance Color Cameras onlyPOWER-UP Mode Alarm Resume AUX ModeAlarm Priority Alarm DwellZone Blank Alarm PatternProportional PAN Turning Limit Stops On or Off Limit StopsPattern Length Park Time MinutesSymptom Unit does not operate TroubleshootingSymptom Alarms not going to preset Symptom Fan does not operateSymptom Alarms not starting a pattern Symptom Motion problemsDome Cleaning MaintenanceBack BOX Electronic Assembly Removal Mechanical SpecificationsSD5 Series Dimension Drawing Ntsc EIA Regulatory Notices Warranty and Return Information
Top Page Image Contents