Pelco c1487-c operation manual Gain/Agc, AGC Mode

Page 31

Turning off power to the Spectra II™ and Spectra Lite™ domes does not reset the camera. Camera settings are retained in memory, and when the power is turned back on, the settings will be the same as they were when it was turned off.

To reset the camera:

1.Program preset 95 (28 if in 32-preset mode; refer to the Preset Functions section) to access the main menu (refer to the Main Menu Access section). The main menu will appear.

2.If the cursor (>) is not beside Camera, move the joystick up or down to position the cursor beside Camera.

3.Press the Iris Open button to enter the Camera submenu.

4.Move the joystick up or down to position the cursor beside Reset Camera.

5.Press the Iris Open button to reset the camera.

GAIN/AGC

AGC Mode

There are three AGC (Automatic Gain Control) modes: auto, on, and off.

In the auto mode, the Spectra II™ and Spectra Lite™ domes automatically adjust the gain– the amount of amplification the camera places on its video information in order to obtain a full 1-volt peak-to-peak video signal out. If the iris is manually opened to its wide-open position and the picture is weak, the AGC can be turned off and the gain increased manually to improve the picture. For instructions on how to do this, refer to the Auto Iris section. When you close the iris, the AGC will turn back on automatically when the lens iris starts closing.

In the on mode the AGC is on all the time.

In the off mode the AGC is off.

To change the AGC mode:

1.Program preset 95 (28 if in 32-preset mode; refer to the Preset Functions section) to access the main menu (refer to the Main Menu Access section). The main menu will appear.

2.If the cursor (>) is not beside Camera, move the joystick up or down to position the cursor beside Camera.

3.Press the Iris Open button to enter the Camera submenu.

4.Move the joystick up or down to position the cursor beside Gain/AGC.

5.Press the Iris Open button to enter the Gain/AGC submenu.

6.Move the joystick up or down to position the cursor beside AGC mode.

7.Press the Iris Open button on your keyboard. A star will appear beside AGC mode and the cursor will move to the right beside the word Auto, On, or Off.

8.Move the joystick up or down to position the cursor beside Auto, On, or Off.

9.SELECT - Press the Iris Open button on your keyboard to select your choice. CANCEL - Press the Iris Close button if you do not want to change the setting.

Pelco Manual C1487M-C (7/99)

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Listed Contents List of Tables List of IllustrationsGeneral Important Safeguards and WarningsMeasures DE Securite Importantes Lower Dome IN-CEILING ModelsBack Box Dome DrivePendant Components Pendant ModelsSpectra II IN-CEILING Components DescriptionModels Spectra II Pendant ComponentsCeiling and Back BOX Preparation Installation for IN-CEILING ModelsSpectra Lite Pendant Components Spectra Lite IN-CEILING ComponentsSuspended Ceiling Installing Back BoxWiring Diagram for Spectra WiringRG6/U Cable Type Maximum DistanceTable B VAC Wiring Distances Back BOX InstallationBack BOX Connections From controller To 4-Wire terminal on circuit boardControl Dome Drive Switch Locations Table C. Switch Settings for SW1For D-type control systems, refer to Table E Baud Rate Switch Setting SW2-6 SW2-7 SW2-8For P-type control systems, refer to Table D 100 117 177 Lower Dome Lower Dome Installation, In-Ceiling ModelsPENDANT-MOUNT Installation Installation for Pendant ModelsOperation SURFACE-MOUNT InstallationScan Speed POWER-UP DisplayPAN and Tilt Functions Auto FlipZoom Spectra II Zoom Preset FunctionsSpectra Lite Zoom Patterns AlarmsRANDOM, FRAME, and Auto Scanning ZonesPark Auxiliary OutputsProgramming the Spectra II and Spectra Lite Backlight Compensation Main Menu AccessZoom Limit Reset CameraDenotes items that apply to the Spectra II only GAIN/AGC AGC ModeAuto Iris GainShutter Speed Sharpness AUTO-FOCUS ModeLine Synchronization White Balance Color Cameras onlyPOWER-UP Mode Alarm Resume AUX ModeAlarm Priority Alarm DwellZone Blank Alarm PatternProportional PAN Turning Limit Stops On or Off Limit StopsPattern Length Park Time MinutesSymptom Unit does not operate TroubleshootingSymptom Motion problems Symptom Fan does not operateSymptom Alarms not going to preset Symptom Alarms not starting a patternBack BOX Electronic Assembly Removal MaintenanceDome Cleaning Mechanical SpecificationsSD5 Series Dimension Drawing Ntsc EIA Regulatory Notices Warranty and Return Information
Top Page Image Contents