Pelco c1487-c operation manual AUX Mode, Alarm Resume

Page 37

To select the power-up mode:

1.Program preset 95 (28 if in 32-preset mode; refer to the Preset Functions section) to access the main menu (refer to the Main Menu Access section). The main menu will appear.

2.If the cursor (>) is not beside Power Up Mode, move the joystick up or down to position the cursor beside Power Up Mode.

3.Press the Iris Open button to enter the Power Up Mode submenu.

4.Move the joystick up or down to cycle through the selections. Stop on the item you want to select.

5.SELECT - Press the Iris Open button on your keyboard to select your choice. CANCEL - Press the Iris Close button if you do not want to change the setting.

AUX MODE

(This section applies to Spectra II™ only.)

This feature defines the output relay as either Normal (under control of the head end), Latching (pressing the AUX key turns on the AUX and the next press of the AUX key turns it off), or Alarm (any alarm input activates the AUX).

To change the AUX mode:

1.Program preset 95 (28 if in 32-preset mode; refer to the Preset Functions section) to access the main menu (refer to the Main Menu Access section). The main menu will appear.

2.If the cursor (>) is not beside AUX, move the joystick up or down to position the cursor beside AUX.

3.Press the Iris Open button to enter the AUX submenu.

4.Move the joystick up or down to position the cursor next to either Aux 1 mode or Aux 2 mode.

5.Press the Iris Open button. The cursor will move to the right beside the word Normal, Latching, or Alarm.

6.Move the joystick up or down to toggle between Normal, Latching, or Alarm.

7.SELECT - Press the Iris Open button on your keyboard to select your choice. CANCEL - Press the Iris Close button if you do not want to change the setting.

ALARM RESUME

(This section applies to Spectra II™ only.)

This mode lets the dome resume its previous activity (scan, pattern, or previous position) after all alarms are cleared.

To change the alarm resume mode:

1.Program preset 95 (28 if in 32-preset mode; refer to the Preset Functions section) to access the main menu (refer to the Main Menu Access section). The main menu will appear.

2.If the cursor (>) is not beside Alarms, Zone Blank, move the joystick up or down to position the cursor beside Alarms, Zone Blank.

3.Press the Iris Open button to enter the Alarms, Zone Blank submenu.

4.Move the joystick up or down to position the cursor beside Alarm Resume.

5.Press the Iris Open button. The cursor will move to the right beside the word On or Off.

Pelco Manual C1487M-C (7/99)

37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Listed Contents List of Tables List of IllustrationsGeneral Important Safeguards and WarningsMeasures DE Securite Importantes Back Box IN-CEILING ModelsDome Drive Lower DomePendant Components Pendant ModelsModels DescriptionSpectra II Pendant Components Spectra II IN-CEILING ComponentsSpectra Lite Pendant Components Installation for IN-CEILING ModelsSpectra Lite IN-CEILING Components Ceiling and Back BOX PreparationSuspended Ceiling Installing Back BoxWiring Diagram for Spectra WiringRG6/U Cable Type Maximum DistanceTable B VAC Wiring Distances Back BOX InstallationBack BOX Connections From controller To 4-Wire terminal on circuit boardControl Dome Drive Switch Locations Table C. Switch Settings for SW1For D-type control systems, refer to Table E Baud Rate Switch Setting SW2-6 SW2-7 SW2-8For P-type control systems, refer to Table D 100 117 177 Lower Dome Lower Dome Installation, In-Ceiling ModelsPENDANT-MOUNT Installation Installation for Pendant ModelsOperation SURFACE-MOUNT InstallationPAN and Tilt Functions POWER-UP DisplayAuto Flip Scan SpeedZoom Spectra II Zoom Preset FunctionsSpectra Lite Zoom RANDOM, FRAME, and Auto Scanning AlarmsZones PatternsPark Auxiliary OutputsProgramming the Spectra II and Spectra Lite Backlight Compensation Main Menu AccessZoom Limit Reset CameraDenotes items that apply to the Spectra II only GAIN/AGC AGC ModeAuto Iris GainShutter Speed Sharpness AUTO-FOCUS ModeLine Synchronization White Balance Color Cameras onlyPOWER-UP Mode Alarm Resume AUX ModeAlarm Priority Alarm DwellZone Blank Alarm PatternProportional PAN Turning Limit Stops On or Off Limit StopsPattern Length Park Time MinutesSymptom Unit does not operate TroubleshootingSymptom Alarms not going to preset Symptom Fan does not operateSymptom Alarms not starting a pattern Symptom Motion problemsBack BOX Electronic Assembly Removal MaintenanceDome Cleaning Mechanical SpecificationsSD5 Series Dimension Drawing Ntsc EIA Regulatory Notices Warranty and Return Information
Top Page Image Contents