Pelco c1487-c operation manual White Balance Color Cameras only, Line Synchronization

Page 35

AUTO SHARPNESS - The cursor moves to one of two choices: On or Off. Move the joystick up or down to toggle between them. Press the Iris Open button to select the choice, or press the Iris Close button if you do not want to change the setting.

SHARPNESS - The cursor moves to a numeric value. Move the joystick up or down to a value. As you change the value, you will see the sharpness change. Press the Iris Open button to select the value, or press the Iris Close button if you do not want to change the setting. If the Auto Sharpness is on, it will change to off when you select a new value.

WHITE BALANCE (COLOR CAMERAS ONLY)

There are three settings for white balance: auto, red-blue, and magenta-green.

To change the white balance settings:

1.Program preset 95 (28 if in 32-preset mode; refer to the Preset Functions section) to access the main menu (refer to the Main Menu Access section). The main menu will appear.

2.If the cursor (>) is not beside Camera, move the joystick up or down to position the cursor beside Camera.

3.Press the Iris Open button to enter the Camera submenu.

4.Move the joystick up or down to position the cursor beside Next.

5.Press the Iris Open button to go to the next camera submenu.

6.Move the joystick up or down to position the cursor beside White Balance.

7.Press the Iris Open button on your keyboard. Another menu will appear with the auto, red-blue, and magenta-green selections.

8.Move the joystick up or down to position the cursor beside one of the choices. Press the Iris Open button on your keyboard.

AUTO WHITE BALANCE - The cursor moves to one of two choices: Auto or Off. Move the joystick up or down to toggle between them. Press the Iris Open button to select the choice, or press the Iris Close button if you do not want to change the setting.

R-B WHITE BALANCE - The cursor moves to a numeric value. Move the joystick up or down to a value. As you change the value, you will see the color change on your monitor. Press the Iris Open button to select the value, or press the Iris Close button if you do not want to change the setting. If Auto White Balance is on, it will change to off when you select a new value.

M-G WHITE BALANCE - The cursor moves to a numeric value. Move the joystick up or down to a value. As you change the value, you will see the color change on your monitor. Press the Iris Open button to select the value, or press the Iris Close button if you do not want to change the setting. If Auto White Balance is on, it will change to off when you select a new value.

LINE SYNCHRONIZATION

(This section applies to Spectra II™ only.)

You can turn the line synchronization on or off.

If it is on, you can adjust the synchronization of the power line voltage so that it is in phase with other cameras. If cameras are out of phase with each other, they may produce what appears to be vertical roll when switching between cameras.

If it is off, the dome synchronizes to an internal clock.

To change the line synchronization settings:

1.Program preset 95 (28 if in 32-preset mode; refer to the Preset Functions section) to access the main menu (refer to the Main Menu Access section). The main menu will appear.

Pelco Manual C1487M-C (7/99)

35

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Listed Contents List of Tables List of IllustrationsMeasures DE Securite Importantes Important Safeguards and WarningsGeneral Lower Dome IN-CEILING ModelsBack Box Dome DrivePendant Components Pendant ModelsSpectra II IN-CEILING Components DescriptionModels Spectra II Pendant ComponentsCeiling and Back BOX Preparation Installation for IN-CEILING ModelsSpectra Lite Pendant Components Spectra Lite IN-CEILING ComponentsSuspended Ceiling Installing Back BoxWiring Diagram for Spectra WiringRG6/U Cable Type Maximum DistanceTable B VAC Wiring Distances Back BOX InstallationBack BOX Connections From controller To 4-Wire terminal on circuit boardControl Dome Drive Switch Locations Table C. Switch Settings for SW1For D-type control systems, refer to Table E Baud Rate Switch Setting SW2-6 SW2-7 SW2-8For P-type control systems, refer to Table D 100 117 177 Lower Dome Lower Dome Installation, In-Ceiling ModelsPENDANT-MOUNT Installation Installation for Pendant ModelsOperation SURFACE-MOUNT InstallationScan Speed POWER-UP DisplayPAN and Tilt Functions Auto FlipSpectra Lite Zoom Preset FunctionsZoom Spectra II Zoom Patterns AlarmsRANDOM, FRAME, and Auto Scanning ZonesPark Auxiliary OutputsProgramming the Spectra II and Spectra Lite Backlight Compensation Main Menu AccessDenotes items that apply to the Spectra II only Reset CameraZoom Limit GAIN/AGC AGC ModeAuto Iris GainShutter Speed Sharpness AUTO-FOCUS ModeLine Synchronization White Balance Color Cameras onlyPOWER-UP Mode Alarm Resume AUX ModeAlarm Priority Alarm DwellZone Blank Alarm PatternProportional PAN Turning Limit Stops On or Off Limit StopsPattern Length Park Time MinutesSymptom Unit does not operate TroubleshootingSymptom Motion problems Symptom Fan does not operateSymptom Alarms not going to preset Symptom Alarms not starting a patternDome Cleaning MaintenanceBack BOX Electronic Assembly Removal Mechanical SpecificationsSD5 Series Dimension Drawing Ntsc EIA Regulatory Notices Warranty and Return Information
Top Page Image Contents