Shopsmith 555970 manual Conventional Routing Operations with the Overarm Router

Page 30

555970

MARK V – MOUNTED OVERARM PIN ROUTER

CONVENTIONAL ROUTING OPERATIONS WITH THE OVERARM ROUTER

The Shopsmith Overarm Pin Router is also well suited for more ordinary routing operations . . . functioning in a very similar fashion to more conventional under-table router set-ups. There are a few differences:

•With the Overarm Router, your rotating bit is almost always in plain view, provid- ing an added measure of accuracy.

•Changing your depth-of cut (and seeing your change as you make it) is a much simpler matter with an Overarm Router. For maximum efficiency, under-table rout- ing requires a special router lifting device. Such devices often expensive, adding a couple of hundred dollars to the cost of a router table.

•The improved visibility of your work-in- process also makes forming stopped cuts (such as travel slots, grooves, dadoes and mortises) much easier and safer with an Overarm Router.

ROUTING AGAINST A TABLE PIN

Against-the-Guide-Pin routing is usually performed with a non-piloted router bit – on a workpiece with irregular or rounded edges that cannot be guided by the Fences. That’s because the job of the pilots (solid or bear- ing-types) on piloted Bits are to control your lateral depth-of-cut . . . and the profile they’re making.

Since non-piloted Bits have no pilots to con- trol their lateral depths-of-cut, you must rely on Guide Pins to control this for you. Some typical against-the-Pin operations include creating special rabbet cuts (usually with straight bits or slot cutters) and making deco-

rative cuts with non-piloted profile Bits. Here’s the step-by-step process.

1.Set up your Overarm Router, following the “General guidelines for overarm routing” on page 18 in the front section of this Manual.

2.Once you get started, always set your depth-of-cut to make your first pass very shallow. Doing so will give you far better control over the accuracy of your cut, since the rotating bit is much less likely to grab or pull your workpiece off your planned profile when your cuts are shallow.

NOTE

In some cases, your lateral depth-of-cut must also be adjusted to produce the pro- file you desire. With straight-edged work- pieces, this can be accomplished by slid- ing your guiding Fence in or out. With ir- regular-shaped edges, just change the size of the Guide Pin you’re using.

3.Screw the appropriate sized Guide Pin into the threaded hole in the center of the Pin Routing Table Insert and tighten it securely.

4.Position the Table Insert as shown in Figure 23 and screw the 1/4" Starter Pin into the threaded hole just to the left of the center hole in the Plate. Tighten se- curely. When installing the Table In- sert, the Starter Pin must always be po- sitioned in the Insert so it is to the left of the Guide Pin.

5.Prepare to make your cut. Lower the Router into the position and lock it se- curely. Turn on your Router motor. Rest- ing the edge of your workpiece against the Starter Pin, ease it gradually into the rotating bit to start your cut. Continue

30

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Mark V Mounted Overarm PIN Router Table of Contents What is PIN ROUTING? IntroductionWhat can I do with this TOOL? Safety Overarm Router SpecificationsGuarding for Routing EYE ProtectionHearing Protection DressGeneral Safety Rules for Power Tools Sawdust and ChipsMounting Router Bits Mark V Mounted Overarm PIN Router Safety Rules for the Shopsmith Overarm Router Care and Maintenance Types Router BitsMark V Mounted Overarm PIN Router Terms to Know Overarm Router Assembly Tools & Supplies NeededInstall Depth Stop ROD Before YOU BeginWhich Mounting Holes ? RE-INSTALL the Mark Worktable Install Your Router Motor in the OverarmInstall the Rear Guard and Dust Collector Assembly Mount the Overarm Router Table Onto the Mark V WorktableMark V Mounted Overarm PIN Router Alignment Adjustment RE-POSITIONING the Depth Control HandleBringing the Insert Flush with the Worktable Surface Adjusting the Brass GIB Router BIT to Guide PIN AlignmentSafety First Using Your Shopsmith Overarm PIN RouterGeneral Guidelines for Both Types of Overarm Routing Mark V Mounted Overarm PIN Router Router Duplication Using SHOP-MADE Fixtures Types of FixturesTypical clamp-in fixture Project made with it HOW to Make SCREW-DOWN and CLAMP-IN Fixtures AN Overview of PIN Routing with FixturesWHY Make a Grooved FIXTURE? Construction of a typical Clamp-in fixture HOW to Make Profile Fixtures HOW to USE PIN Routing FixturesRouting with a screw-down Fixture Routing over a pin with a clamp-in fixture Typical clamp-in fixtureRouting against a pin using a profile fixture Routing with a clamp-in fixtureCutting decorative surface features using a fixture Conventional Routing Operations with the Overarm Router Routing Against a Table PINUsing Piloted Bits for Decorative Edging Use the Pin Routing Table Insert When routing against a pinExternal edges Internal edgesUsing NON-PILOTED Bits for Decorative Edging Making Rabbet CutsSTRAIGHT-LINE Routing Cutting Grooves and Dadoes GroovesDadoes Making stopped cuts using the Fence Repairing furniture and veneersDamaged area on a Cabinet door Cleaning Caring for Your Shopsmith Overarm PIN RouterStructural Joints Storing Your Overarm Router RE-ALIGNING and RE-ADJUSTINGWaxing Do not wax or use solvents on plastic partsMaintenance Troubleshooting Guide Problem Possible Cause SolutionHow to Order Parts Mark V Mounted Overarm PIN Router

555970 specifications

The Shopsmith 555970 is a versatile woodworking tool that embodies the ideal solution for hobbyists and professional woodworkers alike. As a multi-function machine, it combines multiple woodworking capabilities into a singular unit, allowing users to seamlessly transition between various tasks with ease and efficiency.

One of the standout features of the Shopsmith 555970 is its ability to operate as a table saw, bandsaw, drill press, disc sander, and lathe—all in one compact design. This all-in-one functionality eliminates the need for multiple machines, saving both space in the workshop and the expense of purchasing separate tools.

The device is powered by a robust motor that delivers consistent performance, enabling users to tackle a variety of materials, from softwoods to hardwoods. This makes the Shopsmith 555970 an excellent choice for diverse projects, whether constructing furniture, crafting detailed woodwork, or completing home repairs. With adjustable speeds and settings, users can customize their experience according to the specific needs of their project.

One innovative technology integrated into the Shopsmith 555970 is its quick-change tooling system. This feature allows users to switch from one function to another in a matter of minutes. For example, converting from a table saw to a lathe does not require extensive setup; instead, it can be done easily, enhancing workflow and reducing downtime.

Additionally, the Shopsmith 555970 is equipped with a dual-tube design for rigidity and stability, which contributes to safer operation and improved accuracy during cutting and shaping tasks. Safety features such as blade guards and secure locking mechanisms have also been thoughtfully integrated into the design, prioritizing user safety without sacrificing performance.

The compact design of the Shopsmith 555970 makes it particularly appealing for home workshops with limited space. Its dimensions allow it to be stored easily when not in use, catering to those who appreciate functionality without compromising their available workspace.

In summary, the Shopsmith 555970 stands out in the woodworking market for its multifunctionality, powerful motor, user-friendly features, and compact design. Whether you are a professional woodworker or a passionate DIY enthusiast, this machine offers the versatility needed to bring creative woodworking ideas to life.
Top Page Image Contents