Shopsmith 555970 manual Cutting decorative surface features using a fixture

Page 29

MARK V – MOUNTED OVERARM PIN ROUTER

555970

Cutting decorative internal and external edges using a fixture

Figure 21 shows a finished plaque, still at- tached to its fixture. Only the top surface of the edge was cut.

Figure 21. A plaque with external

decorative edging completed. We used

a1/2", non-piloted core box bit to form our example edge.

Step 1. Set your router bit to produce the desired depth-of-cut. To do this, use your fixture to cut out a practice sample of your finished product. Be sure it’s the same thick- ness as the finished piece you plan to make. Use this practice sample to make a few cuts until you achieve your desired profile.

NOTE

When using a fixture to guide your workpiece through decorative edging cuts, you can alter the profiles produced by changing to a Guide Pin that’s smaller than your groove and/or changing the side of the fixture groove you guide against.

During operation, it’s important that you al- ways guide your fixture against the same side of the groove throughout your cut. If you’re using the outside edge of the groove, you must pull against the Guide Pin as you make your cut. If you’re using the inside edge of the groove, you must push against the Guide Pin as you make you cut. Remember . . . changing groove sides in mid- cut will alter the profile of the cut and ruin your edge.

Step 2. Cut the edge. The routing method used is similar to routing against a pin. Re- member to always move the fixture against the rotation of the bit, and keep the same wall of the groove against the Guide Pin at all times. Usually, only two passes are re- quired to achieve the final depth-of-cut. It’s OK to make about 75 percent of the cut on the first pass, and the balance on the second.

Cutting decorative surface features using a fixture

An unlimited variety of attractive surface decorations can be created by guiding an ex- isting (or additional) groove in your fixture over a Guide Pin, such as our Figure 22 ex- ample of cutting a V-groove in the surface of an oval picture frame.

Figure 22. Using a V-groove bit to cut

a decorative surface feature in an

oval picture frame.

Since the entire bit is in contact with the workpiece while making surfacing cuts, you must always use a Guide Pin that’s the same size as the groove in your fixture for safety reasons. As a result, the profile of your cut is controlled entirely by altering the depth- of-cut of the bit. Decorative surfacing cuts cannot be made with a piloted router bit unless a straight bit is used first to form a groove that the pilot can ride in.

29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Mark V Mounted Overarm PIN Router Table of Contents What can I do with this TOOL? What is PIN ROUTING?Introduction Overarm Router Specifications SafetyHearing Protection EYE ProtectionGuarding for Routing DressMounting Router Bits General Safety Rules for Power ToolsSawdust and Chips Mark V Mounted Overarm PIN Router Safety Rules for the Shopsmith Overarm Router Types Router Bits Care and MaintenanceMark V Mounted Overarm PIN Router Terms to Know Tools & Supplies Needed Overarm Router AssemblyWhich Mounting Holes ? Install Depth Stop RODBefore YOU Begin Install Your Router Motor in the Overarm RE-INSTALL the Mark WorktableMount the Overarm Router Table Onto the Mark V Worktable Install the Rear Guard and Dust Collector AssemblyMark V Mounted Overarm PIN Router Bringing the Insert Flush with the Worktable Surface Alignment AdjustmentRE-POSITIONING the Depth Control Handle Router BIT to Guide PIN Alignment Adjusting the Brass GIBGeneral Guidelines for Both Types of Overarm Routing Safety FirstUsing Your Shopsmith Overarm PIN Router Mark V Mounted Overarm PIN Router Types of Fixtures Router Duplication Using SHOP-MADE FixturesTypical clamp-in fixture Project made with it AN Overview of PIN Routing with Fixtures HOW to Make SCREW-DOWN and CLAMP-IN FixturesWHY Make a Grooved FIXTURE? Construction of a typical Clamp-in fixture HOW to USE PIN Routing Fixtures HOW to Make Profile FixturesRouting with a screw-down Fixture Typical clamp-in fixture Routing over a pin with a clamp-in fixtureRouting with a clamp-in fixture Routing against a pin using a profile fixtureCutting decorative surface features using a fixture Routing Against a Table PIN Conventional Routing Operations with the Overarm RouterUse the Pin Routing Table Insert When routing against a pin Using Piloted Bits for Decorative EdgingInternal edges External edgesMaking Rabbet Cuts Using NON-PILOTED Bits for Decorative EdgingSTRAIGHT-LINE Routing Grooves Cutting Grooves and DadoesDadoes Repairing furniture and veneers Making stopped cuts using the FenceDamaged area on a Cabinet door Structural Joints CleaningCaring for Your Shopsmith Overarm PIN Router Waxing RE-ALIGNING and RE-ADJUSTINGStoring Your Overarm Router Do not wax or use solvents on plastic partsMaintenance Problem Possible Cause Solution Troubleshooting GuideHow to Order Parts Mark V Mounted Overarm PIN Router

555970 specifications

The Shopsmith 555970 is a versatile woodworking tool that embodies the ideal solution for hobbyists and professional woodworkers alike. As a multi-function machine, it combines multiple woodworking capabilities into a singular unit, allowing users to seamlessly transition between various tasks with ease and efficiency.

One of the standout features of the Shopsmith 555970 is its ability to operate as a table saw, bandsaw, drill press, disc sander, and lathe—all in one compact design. This all-in-one functionality eliminates the need for multiple machines, saving both space in the workshop and the expense of purchasing separate tools.

The device is powered by a robust motor that delivers consistent performance, enabling users to tackle a variety of materials, from softwoods to hardwoods. This makes the Shopsmith 555970 an excellent choice for diverse projects, whether constructing furniture, crafting detailed woodwork, or completing home repairs. With adjustable speeds and settings, users can customize their experience according to the specific needs of their project.

One innovative technology integrated into the Shopsmith 555970 is its quick-change tooling system. This feature allows users to switch from one function to another in a matter of minutes. For example, converting from a table saw to a lathe does not require extensive setup; instead, it can be done easily, enhancing workflow and reducing downtime.

Additionally, the Shopsmith 555970 is equipped with a dual-tube design for rigidity and stability, which contributes to safer operation and improved accuracy during cutting and shaping tasks. Safety features such as blade guards and secure locking mechanisms have also been thoughtfully integrated into the design, prioritizing user safety without sacrificing performance.

The compact design of the Shopsmith 555970 makes it particularly appealing for home workshops with limited space. Its dimensions allow it to be stored easily when not in use, catering to those who appreciate functionality without compromising their available workspace.

In summary, the Shopsmith 555970 stands out in the woodworking market for its multifunctionality, powerful motor, user-friendly features, and compact design. Whether you are a professional woodworker or a passionate DIY enthusiast, this machine offers the versatility needed to bring creative woodworking ideas to life.
Top Page Image Contents