Shopsmith 555970 manual Making stopped cuts using the Fence, Repairing furniture and veneers

Page 37

MARK V – MOUNTED OVERARM PIN ROUTER

555970

Making stopped cuts using the Fence

A stopped cut is any cut made in a workpiece that does not go completely from end-to-end or from side-to-side. Some ex- amples of stopped cuts include mortises, travel slots and similar cuts. If your project calls for square-ended cuts, the rounded ends left by routing will need to be squared with a chisel once you’ve finished.

Start by following steps one through three outlined above for cutting grooves and dadoes.

4.Limiting the length of your cut. Mark your workpiece where the stop cut is to start and end. Clamp a stop block or a wooden handscrew clamp onto the Fence to limit the length of your cut. If you’re using a stop block, position the block above the worktable so that the sawdust will not be trapped at the side of the stop block (See Fig. 33). If the cut is to be in the center of the workpiece and the workpiece is short enough, use a stop block to limit the travel at both ends.

If the piece is longer than the Fence, screw a suitable extension board to the Fence . . . then clamp the second stop block to that extension board. Another option for long workpieces is to clamp your stop block directly to your workpiece so that it will limit your cut by engaging the edge of the Router Table.

5.With the router motor turned off, posi- tion the workpiece so the bit will be at your starting mark.

Figure 33. Making a stopped cut for

amortise.

6.Turn on the router motor, lower it into your stock, lock it firmly in position, then move the workpiece against the ro- tation of the bit and through the cut un- til it contacts the stop block. If your cut is to be deep, multiple passes will be re- quired.

Repairing furniture and veneers

Another handy use for your Shopsmith Overarm Router is the repair of damaged furniture and veneers. This is accomplished by routing out the damaged area, making a plug to match and then gluing it into the routed area.

1.Install the two-piece Overarm Router Fence, as you would for any straight- line routing operation, positioning the faces of both Fences in perfect alignment with one another.

2.Select a straight router Bit that’s larger in diameter than your damaged area is wide. If the damaged area is wider than any of your Bits, plan on making mul- tiple passes.

37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Mark V Mounted Overarm PIN Router Table of Contents Introduction What is PIN ROUTING?What can I do with this TOOL? Overarm Router Specifications SafetyHearing Protection EYE ProtectionGuarding for Routing DressSawdust and Chips General Safety Rules for Power ToolsMounting Router Bits Mark V Mounted Overarm PIN Router Safety Rules for the Shopsmith Overarm Router Types Router Bits Care and MaintenanceMark V Mounted Overarm PIN Router Terms to Know Tools & Supplies Needed Overarm Router AssemblyBefore YOU Begin Install Depth Stop RODWhich Mounting Holes ? Install Your Router Motor in the Overarm RE-INSTALL the Mark WorktableMount the Overarm Router Table Onto the Mark V Worktable Install the Rear Guard and Dust Collector AssemblyMark V Mounted Overarm PIN Router RE-POSITIONING the Depth Control Handle Alignment AdjustmentBringing the Insert Flush with the Worktable Surface Router BIT to Guide PIN Alignment Adjusting the Brass GIBUsing Your Shopsmith Overarm PIN Router Safety FirstGeneral Guidelines for Both Types of Overarm Routing Mark V Mounted Overarm PIN Router Types of Fixtures Router Duplication Using SHOP-MADE FixturesTypical clamp-in fixture Project made with it AN Overview of PIN Routing with Fixtures HOW to Make SCREW-DOWN and CLAMP-IN FixturesWHY Make a Grooved FIXTURE? Construction of a typical Clamp-in fixture HOW to USE PIN Routing Fixtures HOW to Make Profile FixturesRouting with a screw-down Fixture Typical clamp-in fixture Routing over a pin with a clamp-in fixtureRouting with a clamp-in fixture Routing against a pin using a profile fixtureCutting decorative surface features using a fixture Routing Against a Table PIN Conventional Routing Operations with the Overarm RouterUse the Pin Routing Table Insert When routing against a pin Using Piloted Bits for Decorative EdgingInternal edges External edgesMaking Rabbet Cuts Using NON-PILOTED Bits for Decorative EdgingSTRAIGHT-LINE Routing Grooves Cutting Grooves and DadoesDadoes Repairing furniture and veneers Making stopped cuts using the FenceDamaged area on a Cabinet door Caring for Your Shopsmith Overarm PIN Router CleaningStructural Joints Waxing RE-ALIGNING and RE-ADJUSTINGStoring Your Overarm Router Do not wax or use solvents on plastic partsMaintenance Problem Possible Cause Solution Troubleshooting GuideHow to Order Parts Mark V Mounted Overarm PIN Router

555970 specifications

The Shopsmith 555970 is a versatile woodworking tool that embodies the ideal solution for hobbyists and professional woodworkers alike. As a multi-function machine, it combines multiple woodworking capabilities into a singular unit, allowing users to seamlessly transition between various tasks with ease and efficiency.

One of the standout features of the Shopsmith 555970 is its ability to operate as a table saw, bandsaw, drill press, disc sander, and lathe—all in one compact design. This all-in-one functionality eliminates the need for multiple machines, saving both space in the workshop and the expense of purchasing separate tools.

The device is powered by a robust motor that delivers consistent performance, enabling users to tackle a variety of materials, from softwoods to hardwoods. This makes the Shopsmith 555970 an excellent choice for diverse projects, whether constructing furniture, crafting detailed woodwork, or completing home repairs. With adjustable speeds and settings, users can customize their experience according to the specific needs of their project.

One innovative technology integrated into the Shopsmith 555970 is its quick-change tooling system. This feature allows users to switch from one function to another in a matter of minutes. For example, converting from a table saw to a lathe does not require extensive setup; instead, it can be done easily, enhancing workflow and reducing downtime.

Additionally, the Shopsmith 555970 is equipped with a dual-tube design for rigidity and stability, which contributes to safer operation and improved accuracy during cutting and shaping tasks. Safety features such as blade guards and secure locking mechanisms have also been thoughtfully integrated into the design, prioritizing user safety without sacrificing performance.

The compact design of the Shopsmith 555970 makes it particularly appealing for home workshops with limited space. Its dimensions allow it to be stored easily when not in use, catering to those who appreciate functionality without compromising their available workspace.

In summary, the Shopsmith 555970 stands out in the woodworking market for its multifunctionality, powerful motor, user-friendly features, and compact design. Whether you are a professional woodworker or a passionate DIY enthusiast, this machine offers the versatility needed to bring creative woodworking ideas to life.
Top Page Image Contents