Shopsmith 555970 Routing against a pin using a profile fixture, Routing with a clamp-in fixture

Page 28

555970

MARK V – MOUNTED OVERARM PIN ROUTER

Step 4: Drop the fixture groove over the Table Pin, turn on your router motor, plunge your rotating bit into the workpiece about 1/4" and start moving your fixture (with workpiece attached) in a counter-clockwise motion until you’ve completed your initial cut in the first groove (See Fig. 19).

Figure 19. Routing with a clamp-in fixture.

Step 5: Repeat the process for each groove in your fixture.

Step 6: Remove your completed project from the fixture, clamp a new workpiece blank into position and repeat steps 4, 5 and 6.

Routing against a pin using a profile fixture

Our example profile fixture shown in Fig- ure 20 is used to cut the shaped tops of fence pickets. Similar fixtures could be used for the tops of wall sconces, shaped fence or porch rail balusters and similar projects. You can even make double-ended fixtures, with a dif- ferent design on each end.

Blank workpieces can be inserted and re- moved from profile fixtures very rapidly and they’re usually much easier to make that screw-in or clamp-in fixtures because they require no template (they are the template) and have no grooves.

Figure 20. Construction of a typical

profile fixture.

However, this lack of guiding grooves means that you must be certain to maintain a con- stant, steady pressure against the edge of the fixture throughout the routing process. A momentary loss of concentration could ruin your project and result in personal injury.

Here’s the 4-step process for using a profile fixture:

Step 1: Screw the appropriate sized guide pin into the center hole of the Router Table Insert and align it with the same sized router bit, as explained previously.

Step 2: Position the workpiece on top of the fixture with its tip either flush with or pro- truding 1/8" beyond the end of the fixture so the router Guide Pin will engage the fix- ture before the router bit begins cutting the workpiece. Tap the workpiece firmly with a mallet or the heel of your hand to “seat” it properly in the fixture.

Step 3: Cut one side of your profile. Once again, it’s important that you be careful to maintain a constant, steady pressure against the Guide Pin throughout the cut.

Step 4: Rotate the fixture and cut the oppo- site side of your profile. Remove the workpiece and repeat the process with all subsequent workpieces.

28

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Mark V Mounted Overarm PIN Router Table of Contents Introduction What is PIN ROUTING?What can I do with this TOOL? Safety Overarm Router SpecificationsEYE Protection Hearing ProtectionGuarding for Routing DressSawdust and Chips General Safety Rules for Power ToolsMounting Router Bits Mark V Mounted Overarm PIN Router Safety Rules for the Shopsmith Overarm Router Care and Maintenance Types Router BitsMark V Mounted Overarm PIN Router Terms to Know Overarm Router Assembly Tools & Supplies NeededBefore YOU Begin Install Depth Stop RODWhich Mounting Holes ? RE-INSTALL the Mark Worktable Install Your Router Motor in the OverarmInstall the Rear Guard and Dust Collector Assembly Mount the Overarm Router Table Onto the Mark V WorktableMark V Mounted Overarm PIN Router RE-POSITIONING the Depth Control Handle Alignment AdjustmentBringing the Insert Flush with the Worktable Surface Adjusting the Brass GIB Router BIT to Guide PIN AlignmentUsing Your Shopsmith Overarm PIN Router Safety FirstGeneral Guidelines for Both Types of Overarm Routing Mark V Mounted Overarm PIN Router Router Duplication Using SHOP-MADE Fixtures Types of FixturesTypical clamp-in fixture Project made with it HOW to Make SCREW-DOWN and CLAMP-IN Fixtures AN Overview of PIN Routing with FixturesWHY Make a Grooved FIXTURE? Construction of a typical Clamp-in fixture HOW to Make Profile Fixtures HOW to USE PIN Routing FixturesRouting with a screw-down Fixture Routing over a pin with a clamp-in fixture Typical clamp-in fixtureRouting against a pin using a profile fixture Routing with a clamp-in fixtureCutting decorative surface features using a fixture Conventional Routing Operations with the Overarm Router Routing Against a Table PINUsing Piloted Bits for Decorative Edging Use the Pin Routing Table Insert When routing against a pinExternal edges Internal edgesUsing NON-PILOTED Bits for Decorative Edging Making Rabbet CutsSTRAIGHT-LINE Routing Cutting Grooves and Dadoes GroovesDadoes Making stopped cuts using the Fence Repairing furniture and veneersDamaged area on a Cabinet door Caring for Your Shopsmith Overarm PIN Router CleaningStructural Joints RE-ALIGNING and RE-ADJUSTING WaxingStoring Your Overarm Router Do not wax or use solvents on plastic partsMaintenance Troubleshooting Guide Problem Possible Cause SolutionHow to Order Parts Mark V Mounted Overarm PIN Router

555970 specifications

The Shopsmith 555970 is a versatile woodworking tool that embodies the ideal solution for hobbyists and professional woodworkers alike. As a multi-function machine, it combines multiple woodworking capabilities into a singular unit, allowing users to seamlessly transition between various tasks with ease and efficiency.

One of the standout features of the Shopsmith 555970 is its ability to operate as a table saw, bandsaw, drill press, disc sander, and lathe—all in one compact design. This all-in-one functionality eliminates the need for multiple machines, saving both space in the workshop and the expense of purchasing separate tools.

The device is powered by a robust motor that delivers consistent performance, enabling users to tackle a variety of materials, from softwoods to hardwoods. This makes the Shopsmith 555970 an excellent choice for diverse projects, whether constructing furniture, crafting detailed woodwork, or completing home repairs. With adjustable speeds and settings, users can customize their experience according to the specific needs of their project.

One innovative technology integrated into the Shopsmith 555970 is its quick-change tooling system. This feature allows users to switch from one function to another in a matter of minutes. For example, converting from a table saw to a lathe does not require extensive setup; instead, it can be done easily, enhancing workflow and reducing downtime.

Additionally, the Shopsmith 555970 is equipped with a dual-tube design for rigidity and stability, which contributes to safer operation and improved accuracy during cutting and shaping tasks. Safety features such as blade guards and secure locking mechanisms have also been thoughtfully integrated into the design, prioritizing user safety without sacrificing performance.

The compact design of the Shopsmith 555970 makes it particularly appealing for home workshops with limited space. Its dimensions allow it to be stored easily when not in use, catering to those who appreciate functionality without compromising their available workspace.

In summary, the Shopsmith 555970 stands out in the woodworking market for its multifunctionality, powerful motor, user-friendly features, and compact design. Whether you are a professional woodworker or a passionate DIY enthusiast, this machine offers the versatility needed to bring creative woodworking ideas to life.
Top Page Image Contents