Shopsmith 555970 manual External edges, Internal edges

Page 32

555970

MARK V – MOUNTED OVERARM PIN ROUTER

•The hardness of the stock you’re cutting. If you’re working with hard maple, oak, ash, cherry, hickory or other tough stock, it may be necessary to make two or three passes to produce your full profile with- out burning or tear-out.

Performing these operations is basically the same, whether you’re cutting an external edge or an internal edge.

External edges

1.Set up your Overarm Router, following the “General guidelines for overarm routing” on page 18 in the front section of this Manual and install the Bit of your choice.

2.With your router motor turned off, move the workpiece next to the Bit and adjust your up-down depth-of-cut

NOTE

In some cases, your lateral depth-of-cut must also be adjusted to produce the pro- file you desire. In the case of a bearing-pi- loted Bit, this is accomplished by chang- ing the size of the bearing. Most Bit manu- facturers offer a variety of bearing pilots with the same I.D. (internal diameter) and differing O.D.’s (outside diameters). With

asolid-piloted Bit, the lateral depth-of-cut cannot be altered.

3.Screw the 1/4" diameter Starter Pin into the threaded Starter Pin hole in the Pin Routing Table Insert and tighten it se- curely.

4.Move the workpiece away from the Bit area, turn on the motor and lock every- thing in position to make your first pass. Resting the external edge of your workpiece against the Starter Pin, ease it gradually into the rotating Bit to start

your cut. When the Bit pilot contacts the workpiece edge, gradually rotate the workpiece off the Starter Pin and con- tinue to move the workpiece against the rotation of the bit, pushing steadily against the Bit Pilot, which now serves as your guide. (See Figure 24). If a sec- ond pass is required, repeat the proce- dure until the desired profile is achieved.

Figure 24. Cutting a decorative external edge on an oval picture frame using a solid pilot router bit.

Internal edges

To decorate the internal edges of projects, fol- low steps one through three, as outlined above . . . then move to step four below.

4.Move the workpiece away from the Bit area, turn on the motor and lock every- thing in position to make your first pass. Resting the internal edge of your workpiece against the Starter Pin, pull it against the Pin. Maintain a steady pulling force against the starter pin un- til the Bit pilot contacts the workpiece edge, then move it gradually off the Starter Pin and against the rotation of the Bit, as its pilot takes over as your guide. If additional passes are required, repeat this procedure until the desired profile is achieved.

32

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Mark V Mounted Overarm PIN Router Table of Contents What can I do with this TOOL? What is PIN ROUTING?Introduction Safety Overarm Router SpecificationsEYE Protection Hearing ProtectionGuarding for Routing DressMounting Router Bits General Safety Rules for Power ToolsSawdust and Chips Mark V Mounted Overarm PIN Router Safety Rules for the Shopsmith Overarm Router Care and Maintenance Types Router BitsMark V Mounted Overarm PIN Router Terms to Know Overarm Router Assembly Tools & Supplies NeededWhich Mounting Holes ? Install Depth Stop RODBefore YOU Begin RE-INSTALL the Mark Worktable Install Your Router Motor in the OverarmInstall the Rear Guard and Dust Collector Assembly Mount the Overarm Router Table Onto the Mark V WorktableMark V Mounted Overarm PIN Router Bringing the Insert Flush with the Worktable Surface Alignment AdjustmentRE-POSITIONING the Depth Control Handle Adjusting the Brass GIB Router BIT to Guide PIN AlignmentGeneral Guidelines for Both Types of Overarm Routing Safety FirstUsing Your Shopsmith Overarm PIN Router Mark V Mounted Overarm PIN Router Router Duplication Using SHOP-MADE Fixtures Types of FixturesTypical clamp-in fixture Project made with it HOW to Make SCREW-DOWN and CLAMP-IN Fixtures AN Overview of PIN Routing with FixturesWHY Make a Grooved FIXTURE? Construction of a typical Clamp-in fixture HOW to Make Profile Fixtures HOW to USE PIN Routing FixturesRouting with a screw-down Fixture Routing over a pin with a clamp-in fixture Typical clamp-in fixtureRouting against a pin using a profile fixture Routing with a clamp-in fixtureCutting decorative surface features using a fixture Conventional Routing Operations with the Overarm Router Routing Against a Table PINUsing Piloted Bits for Decorative Edging Use the Pin Routing Table Insert When routing against a pinExternal edges Internal edgesUsing NON-PILOTED Bits for Decorative Edging Making Rabbet CutsSTRAIGHT-LINE Routing Cutting Grooves and Dadoes GroovesDadoes Making stopped cuts using the Fence Repairing furniture and veneersDamaged area on a Cabinet door Structural Joints CleaningCaring for Your Shopsmith Overarm PIN Router RE-ALIGNING and RE-ADJUSTING WaxingStoring Your Overarm Router Do not wax or use solvents on plastic partsMaintenance Troubleshooting Guide Problem Possible Cause SolutionHow to Order Parts Mark V Mounted Overarm PIN Router

555970 specifications

The Shopsmith 555970 is a versatile woodworking tool that embodies the ideal solution for hobbyists and professional woodworkers alike. As a multi-function machine, it combines multiple woodworking capabilities into a singular unit, allowing users to seamlessly transition between various tasks with ease and efficiency.

One of the standout features of the Shopsmith 555970 is its ability to operate as a table saw, bandsaw, drill press, disc sander, and lathe—all in one compact design. This all-in-one functionality eliminates the need for multiple machines, saving both space in the workshop and the expense of purchasing separate tools.

The device is powered by a robust motor that delivers consistent performance, enabling users to tackle a variety of materials, from softwoods to hardwoods. This makes the Shopsmith 555970 an excellent choice for diverse projects, whether constructing furniture, crafting detailed woodwork, or completing home repairs. With adjustable speeds and settings, users can customize their experience according to the specific needs of their project.

One innovative technology integrated into the Shopsmith 555970 is its quick-change tooling system. This feature allows users to switch from one function to another in a matter of minutes. For example, converting from a table saw to a lathe does not require extensive setup; instead, it can be done easily, enhancing workflow and reducing downtime.

Additionally, the Shopsmith 555970 is equipped with a dual-tube design for rigidity and stability, which contributes to safer operation and improved accuracy during cutting and shaping tasks. Safety features such as blade guards and secure locking mechanisms have also been thoughtfully integrated into the design, prioritizing user safety without sacrificing performance.

The compact design of the Shopsmith 555970 makes it particularly appealing for home workshops with limited space. Its dimensions allow it to be stored easily when not in use, catering to those who appreciate functionality without compromising their available workspace.

In summary, the Shopsmith 555970 stands out in the woodworking market for its multifunctionality, powerful motor, user-friendly features, and compact design. Whether you are a professional woodworker or a passionate DIY enthusiast, this machine offers the versatility needed to bring creative woodworking ideas to life.
Top Page Image Contents