Shopsmith 555970 manual Making Rabbet Cuts, Using NON-PILOTED Bits for Decorative Edging

Page 33

MARK V – MOUNTED OVERARM PIN ROUTER

555970

USING NON-PILOTED BITS FOR DECORATIVE EDGING

This method is basically the same as for decorative external or internal edging with a piloted Bit. However, since these Bits have no pilot to control your lateral depth-of-cut, you’ll have to rely on a Guide Pin (of a smaller diameter than your router Bit) to control this for you.

One half the difference between the Guide Pin diameter and the outside diameter of your router Bit will be your lateral depth- of-cut.

If using a smaller Guide Pin fails to produce the desired results on a piece of scrap stock, set the machine up so the Guide Pin and the Bit are offset about the same distance as the lateral depth-of-cut you want.

Re-position the edge of the workpiece against the Guide Pin, turn on your router motor and gradually move the workpiece from the Guide Pin into the Bit, taking a very light pass as first.

round workpieces, build a special V-shaped Fence like the one shown in Figure 25 below.

Figure 25. A shop-made, wooden

V-shaped Fence like the one shown here is used for edging round workpieces with non-piloted router Bits.

MAKING RABBET CUTS

Rabbets are edge or step cuts for such things as the inside back edges of picture frames (See Fig. 26).

NOTE

Since the bit and Guide Pin are not in per- fect alignment during this operation, it’s important that you always keep the workpiece in the same plane throughout the cut. If you begin by feeding the stock into the Bit from a position in front of the Guide Pin and end by feeding the stock into the bit from a position to the left or right of the Guide Pin, you will change your lateral depth-of-cut and not achieve a smooth, consistent profile. It’s a good idea to make some practice cuts before attempt- ing this operation on an actual project piece

When forming decorative edges on straight workpieces with a non-piloted Bit, use your Overarm Router Fence to control your lat- eral depth-of-cut. If you’re working with

Figure 26. Cutting a rabbet in the back side

of a round picture frame.

This method is basically the same as cutting decorative internal edges using a pilot bit . . . except . . . a large diameter straight Bit and a Guide Pin are used.

The following equation will help you deter- mine the size Bit and Guide Pin to use for producing a rabbet of a specific size.

33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Mark V Mounted Overarm PIN Router Table of Contents What is PIN ROUTING? IntroductionWhat can I do with this TOOL? Overarm Router Specifications SafetyHearing Protection EYE ProtectionGuarding for Routing DressGeneral Safety Rules for Power Tools Sawdust and ChipsMounting Router Bits Mark V Mounted Overarm PIN Router Safety Rules for the Shopsmith Overarm Router Types Router Bits Care and MaintenanceMark V Mounted Overarm PIN Router Terms to Know Tools & Supplies Needed Overarm Router AssemblyInstall Depth Stop ROD Before YOU BeginWhich Mounting Holes ? Install Your Router Motor in the Overarm RE-INSTALL the Mark WorktableMount the Overarm Router Table Onto the Mark V Worktable Install the Rear Guard and Dust Collector AssemblyMark V Mounted Overarm PIN Router Alignment Adjustment RE-POSITIONING the Depth Control HandleBringing the Insert Flush with the Worktable Surface Router BIT to Guide PIN Alignment Adjusting the Brass GIBSafety First Using Your Shopsmith Overarm PIN RouterGeneral Guidelines for Both Types of Overarm Routing Mark V Mounted Overarm PIN Router Types of Fixtures Router Duplication Using SHOP-MADE FixturesTypical clamp-in fixture Project made with it AN Overview of PIN Routing with Fixtures HOW to Make SCREW-DOWN and CLAMP-IN FixturesWHY Make a Grooved FIXTURE? Construction of a typical Clamp-in fixture HOW to USE PIN Routing Fixtures HOW to Make Profile FixturesRouting with a screw-down Fixture Typical clamp-in fixture Routing over a pin with a clamp-in fixtureRouting with a clamp-in fixture Routing against a pin using a profile fixtureCutting decorative surface features using a fixture Routing Against a Table PIN Conventional Routing Operations with the Overarm RouterUse the Pin Routing Table Insert When routing against a pin Using Piloted Bits for Decorative EdgingInternal edges External edgesMaking Rabbet Cuts Using NON-PILOTED Bits for Decorative EdgingSTRAIGHT-LINE Routing Grooves Cutting Grooves and DadoesDadoes Repairing furniture and veneers Making stopped cuts using the FenceDamaged area on a Cabinet door Cleaning Caring for Your Shopsmith Overarm PIN RouterStructural Joints Waxing RE-ALIGNING and RE-ADJUSTINGStoring Your Overarm Router Do not wax or use solvents on plastic partsMaintenance Problem Possible Cause Solution Troubleshooting GuideHow to Order Parts Mark V Mounted Overarm PIN Router

555970 specifications

The Shopsmith 555970 is a versatile woodworking tool that embodies the ideal solution for hobbyists and professional woodworkers alike. As a multi-function machine, it combines multiple woodworking capabilities into a singular unit, allowing users to seamlessly transition between various tasks with ease and efficiency.

One of the standout features of the Shopsmith 555970 is its ability to operate as a table saw, bandsaw, drill press, disc sander, and lathe—all in one compact design. This all-in-one functionality eliminates the need for multiple machines, saving both space in the workshop and the expense of purchasing separate tools.

The device is powered by a robust motor that delivers consistent performance, enabling users to tackle a variety of materials, from softwoods to hardwoods. This makes the Shopsmith 555970 an excellent choice for diverse projects, whether constructing furniture, crafting detailed woodwork, or completing home repairs. With adjustable speeds and settings, users can customize their experience according to the specific needs of their project.

One innovative technology integrated into the Shopsmith 555970 is its quick-change tooling system. This feature allows users to switch from one function to another in a matter of minutes. For example, converting from a table saw to a lathe does not require extensive setup; instead, it can be done easily, enhancing workflow and reducing downtime.

Additionally, the Shopsmith 555970 is equipped with a dual-tube design for rigidity and stability, which contributes to safer operation and improved accuracy during cutting and shaping tasks. Safety features such as blade guards and secure locking mechanisms have also been thoughtfully integrated into the design, prioritizing user safety without sacrificing performance.

The compact design of the Shopsmith 555970 makes it particularly appealing for home workshops with limited space. Its dimensions allow it to be stored easily when not in use, catering to those who appreciate functionality without compromising their available workspace.

In summary, the Shopsmith 555970 stands out in the woodworking market for its multifunctionality, powerful motor, user-friendly features, and compact design. Whether you are a professional woodworker or a passionate DIY enthusiast, this machine offers the versatility needed to bring creative woodworking ideas to life.
Top Page Image Contents