Shopsmith 555970 manual Types Router Bits, Care and Maintenance

Page 8

555970

MARK V – MOUNTED OVERARM PIN ROUTER

•When routing oversize stock, always use at least one push block to help control the workpiece firmly against the fence.

•Do not work with stock that is too small or too large to handle safely; that is warped, bowed or cupped; or that has loose knots or other defects.

•Plan the operation before you begin. If you are in doubt about how to complete an operation safely, do not attempt it. You can contact your Shopsmith Customer Service Representative or Store person- nel for advice.

•Secure the router, overarm assembly, depth stop rod, depth control handle, worktable, accessories, safety devices, fences, and fixtures before turning on the motor.

TYPES OF

ROUTER BITS

Router bits come in a wide variety of shapes and sizes designed to be used at very high speeds.

The part of the bit mounted in the router chuck is called the shank and the rounded extension beyond the cutter on some bits is called the pilot. The cutting edge of the bit is called a flute. Router bits have one, two or three flutes and the more flutes there are on the bit, the more cuts that can be made per minute. A higher number of flutes re- duces the load on the motor and produces a smoother cut.

Quality bits are made of high speed steel, solid carbide or carbide-tipped steel. High

speed steel bits are heat treated for extra hardness and to hold keen cutting edges. Carbide bits (solid or tipped) are the finest bits available today. Although more expen- sive, they will outlast high speed steel bits at a 15 to 1 ratio on softwoods and are highly recommended for use on hardwoods, plas- tic laminates, plywood and particleboard.

Router bits are generally classified into four different categories — grooving bits, edge cutting bits, panel bits and laminate and ve- neer trimming bits. (See Chart.)

CARE AND MAINTENANCE

You’ll enjoy longer use of your router bits if you make it a point to handle, use and sharpen them properly.

•Use your router bits only for the job they are intended to do.

•Make sure the bit is mounted rigidly in the collet.

•Learn to cut your workpiece at the proper speed to prevent heat buildup that can cause the loss of bit hardness.

•Between operations, set your bits in a safe place where they will not fall or get hit.

CAUTION

Never use solvent on a bearing piloted bit without first removing the bearing.

•After use, clean bits thoroughly.

•Sharpen your bits with a small slip-stone or oilstone with oil. Hone the face of each cutter with light strokes in one direction. Never hone the outside edge because it re- duces the diameter of the cutter. Hone each cutter edge with the same number of strokes.

•If the cutting edge is nicked, take the bit to a professional sharpening service.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Mark V Mounted Overarm PIN Router Table of Contents What can I do with this TOOL? What is PIN ROUTING?Introduction Safety Overarm Router SpecificationsEYE Protection Hearing ProtectionGuarding for Routing DressMounting Router Bits General Safety Rules for Power ToolsSawdust and Chips Mark V Mounted Overarm PIN Router Safety Rules for the Shopsmith Overarm Router Care and Maintenance Types Router BitsMark V Mounted Overarm PIN Router Terms to Know Overarm Router Assembly Tools & Supplies NeededWhich Mounting Holes ? Install Depth Stop RODBefore YOU Begin RE-INSTALL the Mark Worktable Install Your Router Motor in the OverarmInstall the Rear Guard and Dust Collector Assembly Mount the Overarm Router Table Onto the Mark V WorktableMark V Mounted Overarm PIN Router Bringing the Insert Flush with the Worktable Surface Alignment AdjustmentRE-POSITIONING the Depth Control Handle Adjusting the Brass GIB Router BIT to Guide PIN AlignmentGeneral Guidelines for Both Types of Overarm Routing Safety FirstUsing Your Shopsmith Overarm PIN Router Mark V Mounted Overarm PIN Router Router Duplication Using SHOP-MADE Fixtures Types of FixturesTypical clamp-in fixture Project made with it HOW to Make SCREW-DOWN and CLAMP-IN Fixtures AN Overview of PIN Routing with FixturesWHY Make a Grooved FIXTURE? Construction of a typical Clamp-in fixture HOW to Make Profile Fixtures HOW to USE PIN Routing FixturesRouting with a screw-down Fixture Routing over a pin with a clamp-in fixture Typical clamp-in fixtureRouting against a pin using a profile fixture Routing with a clamp-in fixtureCutting decorative surface features using a fixture Conventional Routing Operations with the Overarm Router Routing Against a Table PINUsing Piloted Bits for Decorative Edging Use the Pin Routing Table Insert When routing against a pinExternal edges Internal edgesUsing NON-PILOTED Bits for Decorative Edging Making Rabbet CutsSTRAIGHT-LINE Routing Cutting Grooves and Dadoes GroovesDadoes Making stopped cuts using the Fence Repairing furniture and veneersDamaged area on a Cabinet door Structural Joints CleaningCaring for Your Shopsmith Overarm PIN Router RE-ALIGNING and RE-ADJUSTING WaxingStoring Your Overarm Router Do not wax or use solvents on plastic partsMaintenance Troubleshooting Guide Problem Possible Cause SolutionHow to Order Parts Mark V Mounted Overarm PIN Router

555970 specifications

The Shopsmith 555970 is a versatile woodworking tool that embodies the ideal solution for hobbyists and professional woodworkers alike. As a multi-function machine, it combines multiple woodworking capabilities into a singular unit, allowing users to seamlessly transition between various tasks with ease and efficiency.

One of the standout features of the Shopsmith 555970 is its ability to operate as a table saw, bandsaw, drill press, disc sander, and lathe—all in one compact design. This all-in-one functionality eliminates the need for multiple machines, saving both space in the workshop and the expense of purchasing separate tools.

The device is powered by a robust motor that delivers consistent performance, enabling users to tackle a variety of materials, from softwoods to hardwoods. This makes the Shopsmith 555970 an excellent choice for diverse projects, whether constructing furniture, crafting detailed woodwork, or completing home repairs. With adjustable speeds and settings, users can customize their experience according to the specific needs of their project.

One innovative technology integrated into the Shopsmith 555970 is its quick-change tooling system. This feature allows users to switch from one function to another in a matter of minutes. For example, converting from a table saw to a lathe does not require extensive setup; instead, it can be done easily, enhancing workflow and reducing downtime.

Additionally, the Shopsmith 555970 is equipped with a dual-tube design for rigidity and stability, which contributes to safer operation and improved accuracy during cutting and shaping tasks. Safety features such as blade guards and secure locking mechanisms have also been thoughtfully integrated into the design, prioritizing user safety without sacrificing performance.

The compact design of the Shopsmith 555970 makes it particularly appealing for home workshops with limited space. Its dimensions allow it to be stored easily when not in use, catering to those who appreciate functionality without compromising their available workspace.

In summary, the Shopsmith 555970 stands out in the woodworking market for its multifunctionality, powerful motor, user-friendly features, and compact design. Whether you are a professional woodworker or a passionate DIY enthusiast, this machine offers the versatility needed to bring creative woodworking ideas to life.
Top Page Image Contents