Shopsmith 555970 manual Adjusting the Brass GIB, Router BIT to Guide PIN Alignment

Page 17

MARK V – MOUNTED OVERARM PIN ROUTER

555970

CAUTION

Before disengaging the Clutch and Handle assembly, always adjust the Depth Stop Rod so it makes contact with the top of the Arm or hold the Dovetail Slide so the Router Motor doesn’t drop and dam- age your workpiece or the Worktable.

ADJUSTING THE BRASS GIB

The tightness of the Brass Gib should be ad- justed so the Router Motor won’t slip and drop abruptly when the Depth Control Handle is unscrewed prior to re-setting your depth-of-cut.

Figure 8. If required, use a 1/8" Allen wrench

to achieve proper Gib pressure.

If it does slip, the Brass Gib is set too loose against the side surface of the Dovetail Slide. To adjust the Gib, use a 1/8" Allen wrench to tighten the four setscrews (26) uniformly in small increments until the proper Gib pressure is achieved (see Figure 8). When ad- justed properly, the Depth Control Handle should move the motor freely without any “slop” between the arm and the dovetail slide.

ROUTER BIT TO GUIDE

PIN ALIGNMENT

When performing pin routing operations, it’s critical that the Router Bit and Guide Pin be in perfect alignment with one another.

To check this alignment, insert a 3/8" diam- eter straight Router Bit into the collet of your Router Motor and tighten securely. Screw the 3/8" Guide Pin into the threaded center hole in the Overarm Router Table Insert. Lower the motor so your Bit is approximately 1" above the Guide Pin.

Figure 9. Use the handle portion of a combination square as a gauge for checking the bit-to-guide-pin alignment at three points, 90° apart.

Use the base of the combination square (See Fig. 9) to check Bit-to-Guide-Pin alignment at three points 90 degrees apart. If the Bit and Guide Pin are not in perfect alignment, front-to-back and/or left-to-right Worktable adjustments will be required.

Front-to-back adjustments are made by loos- ening the MARK V Table Height Lock Knob and using the MARK V’s Table Height ad- justment handles or knobs.

Left-to-right adjustments are made on MARK V Models 505, 510 and 520 machines by loosening the two 1/4"-20 flathead ma- chine screws that hold the Overarm Router

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Mark V Mounted Overarm PIN Router Table of Contents What can I do with this TOOL? What is PIN ROUTING?Introduction Overarm Router Specifications SafetyHearing Protection EYE ProtectionGuarding for Routing DressMounting Router Bits General Safety Rules for Power ToolsSawdust and Chips Mark V Mounted Overarm PIN Router Safety Rules for the Shopsmith Overarm Router Types Router Bits Care and MaintenanceMark V Mounted Overarm PIN Router Terms to Know Tools & Supplies Needed Overarm Router AssemblyWhich Mounting Holes ? Install Depth Stop RODBefore YOU Begin Install Your Router Motor in the Overarm RE-INSTALL the Mark WorktableMount the Overarm Router Table Onto the Mark V Worktable Install the Rear Guard and Dust Collector AssemblyMark V Mounted Overarm PIN Router Bringing the Insert Flush with the Worktable Surface Alignment AdjustmentRE-POSITIONING the Depth Control Handle Router BIT to Guide PIN Alignment Adjusting the Brass GIBGeneral Guidelines for Both Types of Overarm Routing Safety FirstUsing Your Shopsmith Overarm PIN Router Mark V Mounted Overarm PIN Router Types of Fixtures Router Duplication Using SHOP-MADE FixturesTypical clamp-in fixture Project made with it AN Overview of PIN Routing with Fixtures HOW to Make SCREW-DOWN and CLAMP-IN FixturesWHY Make a Grooved FIXTURE? Construction of a typical Clamp-in fixture HOW to USE PIN Routing Fixtures HOW to Make Profile FixturesRouting with a screw-down Fixture Typical clamp-in fixture Routing over a pin with a clamp-in fixtureRouting with a clamp-in fixture Routing against a pin using a profile fixtureCutting decorative surface features using a fixture Routing Against a Table PIN Conventional Routing Operations with the Overarm RouterUse the Pin Routing Table Insert When routing against a pin Using Piloted Bits for Decorative EdgingInternal edges External edgesMaking Rabbet Cuts Using NON-PILOTED Bits for Decorative EdgingSTRAIGHT-LINE Routing Grooves Cutting Grooves and DadoesDadoes Repairing furniture and veneers Making stopped cuts using the FenceDamaged area on a Cabinet door Structural Joints CleaningCaring for Your Shopsmith Overarm PIN Router Waxing RE-ALIGNING and RE-ADJUSTINGStoring Your Overarm Router Do not wax or use solvents on plastic partsMaintenance Problem Possible Cause Solution Troubleshooting GuideHow to Order Parts Mark V Mounted Overarm PIN Router

555970 specifications

The Shopsmith 555970 is a versatile woodworking tool that embodies the ideal solution for hobbyists and professional woodworkers alike. As a multi-function machine, it combines multiple woodworking capabilities into a singular unit, allowing users to seamlessly transition between various tasks with ease and efficiency.

One of the standout features of the Shopsmith 555970 is its ability to operate as a table saw, bandsaw, drill press, disc sander, and lathe—all in one compact design. This all-in-one functionality eliminates the need for multiple machines, saving both space in the workshop and the expense of purchasing separate tools.

The device is powered by a robust motor that delivers consistent performance, enabling users to tackle a variety of materials, from softwoods to hardwoods. This makes the Shopsmith 555970 an excellent choice for diverse projects, whether constructing furniture, crafting detailed woodwork, or completing home repairs. With adjustable speeds and settings, users can customize their experience according to the specific needs of their project.

One innovative technology integrated into the Shopsmith 555970 is its quick-change tooling system. This feature allows users to switch from one function to another in a matter of minutes. For example, converting from a table saw to a lathe does not require extensive setup; instead, it can be done easily, enhancing workflow and reducing downtime.

Additionally, the Shopsmith 555970 is equipped with a dual-tube design for rigidity and stability, which contributes to safer operation and improved accuracy during cutting and shaping tasks. Safety features such as blade guards and secure locking mechanisms have also been thoughtfully integrated into the design, prioritizing user safety without sacrificing performance.

The compact design of the Shopsmith 555970 makes it particularly appealing for home workshops with limited space. Its dimensions allow it to be stored easily when not in use, catering to those who appreciate functionality without compromising their available workspace.

In summary, the Shopsmith 555970 stands out in the woodworking market for its multifunctionality, powerful motor, user-friendly features, and compact design. Whether you are a professional woodworker or a passionate DIY enthusiast, this machine offers the versatility needed to bring creative woodworking ideas to life.
Top Page Image Contents