Slant/Fin VHS-180, VHS-30 Delayed Ignition Cause Remedy, Not Enough Heat Cause Remedy

Page 25

VICTORY II VHS Models

 

DELAYED IGNITION

 

 

CAUSE

REMEDY

 

1.

Pilot flame too low

1.Adjust pilot flame

 

2.

Excessive primary air

2.Adjust primary air shutter

 

3.

Excessive burner input

3.Check and reduce to input shown on rating plate

 

 

 

 

NOT ENOUGH HEAT

 

 

CAUSE

REMEDY

 

1.

Thermostat setting is too low

1.Set thermostat at higher setting

 

2.

Boiler water maintained at too low temperature

2.Set Aquastat at higher setting

 

3.

Circulator not running

3.With thermostat calling for heat, check for power to circulator.

 

 

 

If power OK but circulator not running, replace circulator

 

4.

Boiler water level too low

4.Carefully snap open relief valve handle to determine if boiler

 

 

 

is full of water. If not full of water, check for system leaks and

 

 

 

check water pressure regulator. Repair any system leaks.

 

 

 

Adjust or replace water pressure reducing valve

 

 

 

 

FUMES AND GAS ODORS

 

 

CAUSE

REMEDY

 

1.

Leaks in gas piping or accessories

1.Locate leaks and repair

 

2.

Gas leaks in service line or meter connections

2.Close service supply valve - shut down boiler and notify utility

 

3.

Adverse draft condition in boiler room

3. Check air supply and venting system

 

4.

Condensation trap is not full of water

4.Check and fill with water

 

5.

Venting system is physically damaged

5.Check carefully and repair. Also, see “Venting System Regular

 

 

 

Inspection”

 

6.

Over-firing

6.Adjust gas input to that shown on boiler rating plate

 

 

 

 

BURNER SHORT CYCLES

 

 

CAUSE

REMEDY

 

1.

Thermostat heat anticipator set too low

1.Reset anticipator

 

2.

Excessive pressure drop due to excess venting system

2.Venting system must be corrected

 

3.

Blockage or restriction in venting system

3.Check and repair

 

4.

Defective air flow switch (out of adjustment)

4.DO NOT adjust, replace

IF REPLACEMENT PARTS ARE NEEDED

When parts are needed, refer to boiler model and serial number shown on the boiler name/rating plate. Refer to publication number VHS-10PL Victory II replacement parts for part numbers. Whenever possible refer to the original order by number and date.

Control identification and replacement should not be attempted by unskilled personnel. Only simple,

easily-identified controls and parts may be obtained locally. All other controls and parts should be identified by and ordered from Slant/Fin. Relief/Safety valves must be ASME rated for the pressure and gross output of the boiler.

For replacement parts, heating contractors should con- tact their Slant/Fin boiler distributor.

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Victory 485 Victory II VHS ModelsSafety Installation RequirementsNatural GAS-FIRED Boiler Location Liquefied Petroleum L.P. Propane GAS-FIRED Boiler LocationFlue GAS Venting Requirements Boiler Room AIR Supply and VentilationApproved Venting Applications Category II and III Venting Heat-Fab Saf-T Vent System Victory II Horizontal Sidewall Venting Victory II VHS Models Victory II VHS Models Venting Requirements Vent Connector MaterialMasonry Vitreous Tile-Lined Chimney not metal lined Connector RequirementsAdditional National Fuel Gas Code Boiler Gas Appliance Type B Venting and Metal-Lined Masonry ChimneyVictory II VHS Models Victory II VHS Models Venting System Regular Inspection Electrical WiringGAS Piping Supply and Return Water PipingCirculating Systems Air Control SystemVictory II VHS Models Piping Arrangement Operating INSTRUCTIONS, Basic Operating Instructions Safety InformationVictory II VHS Models Gas Rate Table Safety CheckCare and Maintenance Inspection During Heating Season Annual Inspection and CleaningVictory II Boiler Sequence of Operations Burners will not SHUT-OFF Cause Remedy Burners Fail to Operate Cause RemedyFlash BACK-BURNING AT Orifices Cause Remedy Not Enough Heat Cause Remedy Delayed Ignition Cause RemedyFumes and GAS Odors Cause Remedy Burner Short Cycles Cause RemedyAppendix a SLANT/FIN CORPORATION, Greenvale, N.Y Phone 516

VHS-180, VHS-30 specifications

Slant/Fin, a prominent name in the heating industry, offers the VHS series, which includes the VHS-30 and VHS-180, two highly efficient hot water boilers designed for residential and light commercial applications. These units are distinguished by their durability, performance, and advanced technologies, making them ideal for a variety of heating needs.

The VHS-30 boasts a compact design, making it suitable for installations in limited spaces while still providing robust heating capabilities. It offers an output of 30,000 BTU, making it efficient for smaller buildings or homes. Conversely, the VHS-180 is designed for larger applications, delivering a powerful 180,000 BTU output, ensuring that even the most demanding spaces remain comfortably heated.

One of the standout features of both models is their ability to operate with natural gas or propane, providing flexibility based on regional gas availability and user preference. This adaptability is further enhanced by their advanced combustion technology, which allows for an efficient and clean burn. Both models incorporate a pressurized hot water boiler design which enhances their energy efficiency by maximizing heat transfer from the burner to the water.

In terms of construction, both the VHS-30 and VHS-180 are built with high-quality components designed for longevity. They feature a durable cast iron heat exchanger, which not only improves the lifespan of the unit but also contributes to its high thermal efficiency. The units are also equipped with state-of-the-art controls that allow users to monitor and adjust settings easily, ensuring optimal performance and energy savings.

Safety is another key aspect of the VHS series. Both models are equipped with numerous safety features, including a high limit temperature control, automatic restart, and a safety valve, ensuring peace of mind for homeowners and building operators alike.

Moreover, the VHS series also emphasizes ease of maintenance. The design allows for straightforward access to all critical components, making servicing and routine maintenance more manageable for technicians. As a result, this leads to reduced downtime and longer service intervals.

In conclusion, the Slant/Fin VHS-30 and VHS-180 are exemplary choices for anyone in need of reliable and efficient hot water heating solutions. Their combination of advanced technology, quality construction, and user-friendly features make them a top choice for both residential and light commercial heating applications. The VHS series stands as a testament to Slant/Fin's commitment to innovation and customer satisfaction in the heating market.
Top Page Image Contents