Marmitek TOTALGUARD manual Motion Detector MS90, Registering a Door/Window Sensor

Page 15

BASIC OPTIONS

4.1.3 Registering a Door/Window Sensor

1. To access the menu, press the menu or menu button. The display will now read ‘ENTER PIN’.

2.Enter your 4-digit PIN code (factory setting 0000. See 8.3 for changing the PIN code). For every digit entered, a * will appear on the display.

3.When the PIN code has been entered correctly, the word ‘INSTALL’ will show up on the display.

4.Press OK.

5.Open your door or window. The console will beep to confirm. The display will read ‘ZONE 1 SET’.

☺A memory space for a sensor is called a zone. If you have more than 1 sensor installed, it will read e.g. ZONE 2 SET, ZONE 3 SET, … ZONE 30 SET.

☺You can choose in which zone you want to install the sensor. If you want to install the sensor in zone 3, press 3 on the number pad before executing step 5.

☺You will find a table in which you can write down which zone contains which sensor at the back of this user manual. We advise you to write down which sensor you have registered in which zone

6.Repeat step 5 for every door/window sensor you wish to register.

7.Press CLEAR to go back to the main menu. Press CLEAR again to quit the menu. To confirm your choice, press 1 for Yes or 2 for No. If you choose Yes, you will quit the menu. If you choose No, you go back to the main menu.

☺Read chapter 12 for information on replacing the batteries.

4.2 Motion Detector MS90

1. Battery compartment.

2. Control Indicator – Lights up when a signal is transmitted.

3. TEST button.

4. Sensitivity switch 1/2 – In setting 1 the sensor will instantly react to movement, in setting 2 the sensor is less sensitive and will only react after registering two movements.

5. Tamper contact.

5

4.2.1Mounting the Motion Detector MS90 The motion detector works by detecting changes in temperature. Do not mount the detector too close to a heater or air conditioner.

2

4

3

1

The motion detector has a range of 6-10 m and an angle of 90°. Because of the special lens the sensor ‘looks down’. Always mount the MS90 at a height of about 180 cm from the floor and place it in such a way that the detector can cover the area you want to secure. The mounting bracket can be placed at an angle (90°) or directly against the wall.

SAFEGUARD / TOTALGUARD

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Safeguardsafeguard TOTALGUARDTOTALGUARDtm Basic Options Introduction Safety warningsExtra Options Introduction Safety warnings Your Marmitek surveillance system Contents of your setImportant properties Marmitek TotalGuard-systeemSecurity console Signal rangeInstalling the console Mounting the console onto the wall Setting the console on a flat surfaceMounting the security console MenusP T I O N S Choosing your languageMenu in English Registering the Key Chain Remote Control Installing remote controlsKey Chain Remote Control KR21 Using the Key Chain Remote ControlRegistering the Comfort Remote Control Using the Comfort Remote ControlInstalling the sensors Using the Door/Window SensorDoor/Window Sensor DS90 Registering a Door/Window Sensor Motion Detector MS90Using the Motion Detector Test mode Testing the location of your motion detectorRegistering a Motion Detector Setting up the security console SC9000 Setting the clockSmoke Detector SD10 / SD90 Storing phone numbers Recording your own messagePhone Setting the alarm Using the security systemSwitching on the ARM Home function Panic alarmSiren What happens when the alarm goes off?Error messages Disarming the systemIntroduction Prevention and comfort ‘Home Automation’Alarm functions of the Lamp/Dimmer Modules Comfort functions of the KR21 Key Chain Remote ControlAddressing your modules Comfort functions of the security console Comfort functions of the SH624 Comfort Remote ControlSetting the timer Switch 4 in SettingRandom Clearing the timer settingsDaily Once onlySetting the delays Advanced system functionsClearing the memory of your security system Activating the chime Changing the access code PINDisarming the siren for silent alarm Advanced security functionsAdding a wired sensor to the Door/Window Sensor DS90 Using wired inputsDeregistering a Door/Window Sensor Emergency sensors always modeChecking the status of the security system Installing an extra siren Marmitek PH7208, art. noAdvanced Home Automation functions Deregistering a Motion DetectorBasic address for Home Automations functions Using an external universal sirenC1 and C2 Telephone functions Calling the security systemActivating the call-in function Console 4xAA batteries Operating the alarm functions via an outside phoneChanging the batteries Operate lights and equipment via an outside phoneMotion Detector MS90 2x AA batteries Key Chain Remote Control KR21 2x CR2016 batteriesComfort Remote Control SH624 4x AAA batteries Door/Window Sensor DS90 2x AAA batteriesFrequently asked questions Tabel Sensors Standard for TotalGuard, optional for SafeGuard Technical DataMarmitek BV PO. BOX 4257 5604 EG Eindhoven Netherlands Declaration of Conformity

TOTALGUARD specifications

Marmitek TOTALGUARD is a comprehensive security solution designed to enhance the safety and security of homes and businesses. This advanced system integrates cutting-edge technologies to provide a robust protective measure against unauthorized access, theft, and other security threats.

One of the standout features of TOTALGUARD is its user-friendly interface. The system is designed for simplicity, allowing users to easily control and monitor their security settings via a dedicated mobile app. This app offers real-time notifications and allows users to receive alerts about any suspicious activities, ensuring immediate response to potential threats.

TOTALGUARD employs a range of high-tech sensors and cameras that deliver high-definition video surveillance around the clock. Its motion detection capabilities are finely tuned, allowing the system to differentiate between normal activity and potential intrusions. This minimizes false alarms, giving users peace of mind that their property is protected without the constant interruptions of unnecessary alerts.

The system is also equipped with smart home integration features, making it compatible with popular smart home devices. This connectivity means that homeowners can integrate their security system with other elements of their smart home – such as lighting and climate control – to create a comprehensive safety net. When an alert is triggered, smart lights can turn on to deter intruders, and connected devices can alert users to any unusual activity in their vicinity.

One of the key characteristics of the TOTALGUARD system is its scalability. Whether you live in a small apartment or manage a large commercial facility, the system can be expanded by adding more sensors, cameras, and modules as needed. This adaptability makes it an ideal choice for a variety of users and settings.

In addition, TOTALGUARD features advanced encryption protocols that ensure the security of data transmission between devices, safeguarding sensitive information from cyber threats. This level of security is crucial in today's digital landscape where security breaches can occur remotely.

Lastly, the Marmitek TOTALGUARD system is designed to be easily installed without the need for professional assistance, making it accessible to a wide range of consumers. With its combination of advanced technology, ease of use, and flexibility, TOTALGUARD represents a formidable solution for anyone looking to enhance their security measures in an increasingly uncertain world.
Top Page Image Contents