Marmitek TOTALGUARD manual Advanced system functions, Setting the delays

Page 26

EXTRA OPTIONS

8. Advanced system functions

8.1 Setting the delays

You can set a number of delay times via the menu DELAYS:

ENTRY DELAY

The time you get to switch off the system after entering your house (factory setting 30 seconds).

EXIT DELAY

The time you get before the system is switched on when you leave your house (factory setting 60 seconds).

ANSWER DELAY

Delay before the system picks up the phone when dialling in (11.2, factory setting 5 seconds).

DIAL DELAY

Delay before the system calls out in case of an alarm (factory setting 30 seconds).

Setting the delays:

1. To access the menu, press the menu or menu button. The display will now read ‘ENTER PIN’.

2.Enter your 4-digit PIN code (factory setting 0000. See 8.3 for changing the PIN code). For every digit entered, a * will appear on the display.

3.When the PIN code has been entered correctly, the word ‘INSTALL’ will show up on the display.

4. Use the menu buttons / to go to menu item 8. DELAYS. Press OK to select this menu item. You can also go to this menu item directly by pressing an 8 on the number pad.

5.Select ENTRY DELAY, EXIT DELAY, ANSWER DELAY or DIAL DELAY and press OK.

6.Enter the time required (1-99 seconds). Press OK. Press CLEAR to delete the values entered.

7.Press CLEAR again to quit the menu.

☺The entry delay only works for the DS90 Door/Window Sensor if set to MAX. MS90 motion detectors will respond instantly.

8.2 Clearing the memory of your security system

You can delete sensors, remote controls, timers or all settings via the menu MEMORY CLEAR.

☺The PIN code is never erased. This code can only be reset by a Marmitek Authorised Service Center.

1. To access the menu, press the menu or menu button. The display will now read ‘ENTER PIN’.

2.Enter your 4-digit PIN code (factory setting 0000. See 8.3 for changing the PIN code). For every digit entered, a * will appear on the display.

3.When the PIN code has been entered correctly, the word ‘INSTALL’ will show up on the display.

4. Use the menu buttons / to go to menu item 6. MEMORY CLEAR. Press OK to select this menu item. You can also go to this menu item directly by pressing a 6 on the number pad.

5.Select CLEAR ALL SENSORS, CLEAR ALL REMOTES, CLEAR ALL TIMERS or MASTER RESET.

6.You are now asked to CONFIRM CLR. Press 1 for Yes or 2 for No.

7.Press CLEAR again to quit the menu.

CLEAR ALL SENSORS

emove a registered sensor.

CLEAR ALL REMOTES

Remove a registered remote control or SD10 smoke detector.

CLEAR ALL TIMERS

Remove all timer settings at once.

MASTER RESET

Clear the memory

26

MARMITEK

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Safeguardsafeguard TOTALGUARDTOTALGUARDtm Introduction Safety warnings Basic OptionsExtra Options Introduction Safety warnings Contents of your set Your Marmitek surveillance systemMarmitek TotalGuard-systeem Important propertiesSignal range Security consoleInstalling the console Menus Setting the console on a flat surfaceMounting the security console Mounting the console onto the wallChoosing your language P T I O N SMenu in English Using the Key Chain Remote Control Installing remote controlsKey Chain Remote Control KR21 Registering the Key Chain Remote ControlUsing the Comfort Remote Control Registering the Comfort Remote ControlDoor/Window Sensor DS90 Installing the sensorsUsing the Door/Window Sensor Motion Detector MS90 Registering a Door/Window SensorRegistering a Motion Detector Using the Motion DetectorTest mode Testing the location of your motion detector Smoke Detector SD10 / SD90 Setting up the security console SC9000Setting the clock Phone Storing phone numbersRecording your own message Using the security system Setting the alarmPanic alarm Switching on the ARM Home functionDisarming the system What happens when the alarm goes off?Error messages SirenPrevention and comfort ‘Home Automation’ Introduction Addressing your modules Alarm functions of the Lamp/Dimmer Modules Comfort functions of the KR21 Key Chain Remote Control Switch 4 in Setting Comfort functions of the SH624 Comfort Remote ControlSetting the timer Comfort functions of the security consoleOnce only Clearing the timer settingsDaily RandomClearing the memory of your security system Setting the delaysAdvanced system functions Advanced security functions Changing the access code PINDisarming the siren for silent alarm Activating the chimeUsing wired inputs Adding a wired sensor to the Door/Window Sensor DS90Emergency sensors always mode Deregistering a Door/Window SensorDeregistering a Motion Detector Installing an extra siren Marmitek PH7208, art. noAdvanced Home Automation functions Checking the status of the security systemUsing an external universal siren Basic address for Home Automations functionsC1 and C2 Activating the call-in function Telephone functionsCalling the security system Operate lights and equipment via an outside phone Operating the alarm functions via an outside phoneChanging the batteries Console 4xAA batteriesDoor/Window Sensor DS90 2x AAA batteries Key Chain Remote Control KR21 2x CR2016 batteriesComfort Remote Control SH624 4x AAA batteries Motion Detector MS90 2x AA batteriesFrequently asked questions Tabel Sensors Technical Data Standard for TotalGuard, optional for SafeGuardDeclaration of Conformity Marmitek BV PO. BOX 4257 5604 EG Eindhoven Netherlands
Top Page Image Contents