Marmitek TOTALGUARD manual Emergency sensors always mode, Deregistering a Door/Window Sensor

Page 29

EXTRA OPTIONS

9.5 Emergency sensors (always mode)

Your system also gives you the option to turn any sensor registered with the system into a so-called emergency sensor. An emergency sensor will also activate the security system when the system is not switched on. When an emergency sensor triggers an alarm, you will hear ‘Alarm cause by emergency sensor’ before the spoken message you recorded.

A few examples:

•A panic button connected to the wired input on the console.

•A door or window that should not be opened at any time.

•A temperature or level sensor that warns you when a certain value or level is exceeded.

Transforming a sensor:

1. To access the menu, press the menu or menu button. The display will now read ‘ENTER PIN’.

2.Enter your 4-digit PIN code (factory setting 0000. See 8.3 for changing the PIN code). For every digit entered, a * will appear on the display.

3.When the PIN code has been entered correctly, the word ‘INSTALL’ will show up on the display.

4.

Use the menu buttons

/

to go to menu item 7. OPTIONS. Press OK to select this menu item. You can also go to this menu

 

item directly by pressing a 7 on the number pad.

5.

Use the menu buttons

/

to go to menu item SENSOR MODE. Press OK to select this menu item.

6.The display now reads SET ALWAYS SENSORS. You can see on your display (top and bottom) which zones and sensors have been registered.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

S E T A L W A Y S

S E N S O R S

17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

7.If you want to turn zone 31 into an emergency sensor, enter 31 on the number pad and press OK. Zone number 31 will start flashing.

8.If you also want to turn zone 5 into an emergency sensor, enter 5 on the number pad and press OK. Zone number 5 will start flashing.

9.If you want to turn zone 31 into a normal sensor again, enter 31 on the number pad and press OK. Zone 31 will stop flashing. 10.Press CLEAR again to quit the menu.

☺Make sure the DS90 Door/Window Sensor is set to MIN if you want the message to be passed on without a delay (see 8.1).

9.6 Deregistering a Door/Window Sensor

1. To access the menu, press the menu or menu button. The display will now read ‘ENTER PIN’.

2.Enter your 4-digit PIN code (factory setting 0000. See 8.3 for changing the PIN code). For every digit entered, a * will appear on the display.

3.When the PIN code has been entered correctly, the word ‘INSTALL’ will show up on the display.

4.Press OK.

5.Enter the number of the zone you want to erase on the number pad and press CLEAR.

6.You are asked to confirm CLEAR ZONE 1. YES 2. NO.

7.Press 1 to erase the zone. The zone number is shown on the display.

8.Press CLEAR again to quit the menu.

☺Zones 31 and 32 cannot be erased.

SAFEGUARD / TOTALGUARD

29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Safeguardsafeguard TOTALGUARDTOTALGUARDtm Basic Options Introduction Safety warningsExtra Options Introduction Safety warnings Your Marmitek surveillance system Contents of your setImportant properties Marmitek TotalGuard-systeemSecurity console Signal rangeInstalling the console Mounting the security console Setting the console on a flat surfaceMenus Mounting the console onto the wallP T I O N S Choosing your languageMenu in English Key Chain Remote Control KR21 Installing remote controlsUsing the Key Chain Remote Control Registering the Key Chain Remote ControlRegistering the Comfort Remote Control Using the Comfort Remote ControlDoor/Window Sensor DS90 Installing the sensorsUsing the Door/Window Sensor Registering a Door/Window Sensor Motion Detector MS90Registering a Motion Detector Using the Motion DetectorTest mode Testing the location of your motion detector Smoke Detector SD10 / SD90 Setting up the security console SC9000Setting the clock Phone Storing phone numbersRecording your own message Setting the alarm Using the security systemSwitching on the ARM Home function Panic alarmError messages What happens when the alarm goes off?Disarming the system SirenIntroduction Prevention and comfort ‘Home Automation’Addressing your modules Alarm functions of the Lamp/Dimmer ModulesComfort functions of the KR21 Key Chain Remote Control Setting the timer Comfort functions of the SH624 Comfort Remote ControlSwitch 4 in Setting Comfort functions of the security consoleDaily Clearing the timer settingsOnce only Random Clearing the memory of your security system Setting the delays Advanced system functions Disarming the siren for silent alarm Changing the access code PINAdvanced security functions Activating the chimeAdding a wired sensor to the Door/Window Sensor DS90 Using wired inputsDeregistering a Door/Window Sensor Emergency sensors always modeAdvanced Home Automation functions Installing an extra siren Marmitek PH7208, art. noDeregistering a Motion Detector Checking the status of the security systemBasic address for Home Automations functions Using an external universal sirenC1 and C2 Activating the call-in function Telephone functionsCalling the security system Changing the batteries Operating the alarm functions via an outside phoneOperate lights and equipment via an outside phone Console 4xAA batteriesComfort Remote Control SH624 4x AAA batteries Key Chain Remote Control KR21 2x CR2016 batteriesDoor/Window Sensor DS90 2x AAA batteries Motion Detector MS90 2x AA batteriesFrequently asked questions Tabel Sensors Standard for TotalGuard, optional for SafeGuard Technical DataMarmitek BV PO. BOX 4257 5604 EG Eindhoven Netherlands Declaration of Conformity
Top Page Image Contents