Marmitek TOTALGUARD manual Addressing your modules, Alarm functions of the Lamp/Dimmer Modules

Page 23

BASIC OPTIONS

7.2 Addressing your modules

An address can be set for every Marmitek X-10 module. This address consists of a HOUSECODE (A-P) and a UNITCODE (1-16). The HOUSECODE of all your components needs to be set to the same letter code (keep all the HOUSECODES set to A. See 10.6 for more information.). With the UNITCODE you can give every module its own number, so that they can be individually controlled (via the number pad on your console or with the SH624 Comfort Remote Control).

7.3Installing the LM12 Lamp/Dimmer Module (standard for TotalGuard, optional for SafeGuard)

1.HOUSECODE SWITCH

To set up the system address. Leave the switch set to A.

2.UNITCODE SWITCH

To set up the module number. Leave the switch set to 1.

3.WALL SOCKET

To connect the lamps you want to switch using the module.

4.FUSE

The fuse protects the lamp/dimmer module against a power overload. If the fuse blows, it can only be replaced by another fuse of the same type.

1	2
3	4

INSTALLATION LM12:

Plug the lamp/dimmer module into a free wall socket and plug your lamp (40-300W) into the module. To avoid damage, do not plug in any other loads - such as household equipment or TL/PL lights -

into the module. Please use an AM12 Device/Switch module or a LM15 Bayonet Lamp Module for these types of loads.

7.4 Alarm functions of the Lamp/Dimmer Modules

When switching on the system via the console, the lamps on A1 and A2 will be switched on during the exit delay. As soon as the system is activated, the lamp will be switched off.

When switching on the alarm via your remote control, the lamps will be switched on and off quickly to indicate the system is activated (comparable to the alarm system on your car).

In the case of an alarm the lights connected to lamp/dimmer modules with addresses A1 and A2 will flash. After 4 minutes the lights will remain on.

7.5Comfort functions of the KR21 Key Chain Remote Control

☺Switch and dim lights remotely. Switch the garden lamps on from your bedroom when you hear suspicious noises.

Press the ‘LIGHTS ON’ button. The lamps on addresses A1 and A2 will be switched on.

Press the ‘LIGHTS OFF’ button. The lamps on addresses A1 and A2 will be switched off.

SAFEGUARD / TOTALGUARD

23

Image 23

Contents Safeguardsafeguard TOTALGUARDTOTALGUARDtm Basic Options Introduction Safety warningsExtra Options Introduction Safety warnings Your Marmitek surveillance system Contents of your setImportant properties Marmitek TotalGuard-systeemSecurity console Signal rangeInstalling the console Mounting the console onto the wall Setting the console on a flat surfaceMounting the security console MenusP T I O N S Choosing your languageMenu in English Registering the Key Chain Remote Control Installing remote controlsKey Chain Remote Control KR21 Using the Key Chain Remote ControlRegistering the Comfort Remote Control Using the Comfort Remote ControlDoor/Window Sensor DS90 Installing the sensorsUsing the Door/Window Sensor Registering a Door/Window Sensor Motion Detector MS90Registering a Motion Detector Using the Motion DetectorTest mode Testing the location of your motion detector Smoke Detector SD10 / SD90 Setting up the security console SC9000Setting the clock Phone Storing phone numbersRecording your own message Setting the alarm Using the security system Switching on the ARM Home function Panic alarmSiren What happens when the alarm goes off?Error messages Disarming the systemIntroduction Prevention and comfort ‘Home Automation’Addressing your modules Alarm functions of the Lamp/Dimmer ModulesComfort functions of the KR21 Key Chain Remote Control Comfort functions of the security console Comfort functions of the SH624 Comfort Remote ControlSetting the timer Switch 4 in SettingRandom Clearing the timer settingsDaily Once onlyClearing the memory of your security system Setting the delaysAdvanced system functions Activating the chime Changing the access code PINDisarming the siren for silent alarm Advanced security functionsAdding a wired sensor to the Door/Window Sensor DS90 Using wired inputsDeregistering a Door/Window Sensor Emergency sensors always modeChecking the status of the security system Installing an extra siren Marmitek PH7208, art. noAdvanced Home Automation functions Deregistering a Motion DetectorBasic address for Home Automations functions Using an external universal sirenC1 and C2 Activating the call-in function Telephone functionsCalling the security system Console 4xAA batteries Operating the alarm functions via an outside phoneChanging the batteries Operate lights and equipment via an outside phoneMotion Detector MS90 2x AA batteries Key Chain Remote Control KR21 2x CR2016 batteriesComfort Remote Control SH624 4x AAA batteries Door/Window Sensor DS90 2x AAA batteriesFrequently asked questions Tabel Sensors Standard for TotalGuard, optional for SafeGuard Technical DataMarmitek BV PO. BOX 4257 5604 EG Eindhoven Netherlands Declaration of Conformity